The Kenmore 110.68102310 is a top-loading washing machine with a 3.5 cubic foot capacity, featuring multiple wash cycles, water temperature selections, and a durable stainless steel wash basket. This manual provides essential information for troubleshooting, maintenance, and repair procedures to ensure optimal performance and longevity of your appliance. Below are key sections covering safety, components, diagnostics, repair instructions, and maintenance guidelines.
Before attempting any repair, ensure the washer is unplugged from the electrical outlet and water supply lines are shut off. Use proper tools and personal protective equipment.
| Hazard | Precaution |
|---|---|
| Electrical Shock | Unplug machine before servicing. Verify power is off with a voltage tester. |
| Water Damage | Turn off both hot and cold water supply valves. Have towels ready for spills. |
| Sharp Edges | Wear cut-resistant gloves when handling internal components. |
| Heavy Parts | Lift with proper technique or use assistance for tub, motor, or counterweight. |
| Chemical Exposure | Use gloves when handling detergents, cleaners, or lubricants. |
Key components: Control panel, Lid switch, Water inlet valve, Pump, Drive motor, Transmission, Agitator, Wash basket, Suspension rods, Balance ring, Timer, Lid lock assembly.
WARNING! Do not bypass safety components like the lid switch.
The control may display error codes. Refer to the table below for common issues.
| Code/Symptom | Possible Cause | Corrective Action |
|---|---|---|
| F1 / F2 | Water fill time exceeded | Check water supply, inlet valve, pressure switch. |
| F5 / F6 | Drain time exceeded | Inspect drain hose, pump, and obstructions. |
| F7 / F8 | Motor control fault | Test motor, wiring, and control board. |
| No power | Power cord, outlet, or lid switch | Verify outlet has power; test lid switch continuity. |
| No agitation | Drive belt, motor, or transmission | Check belt tension; test motor; inspect coupling. |
| No spin | Lid switch, motor, or brake | Test lid switch; check motor operation; inspect brake assembly. |
| Leaking water | Hoses, pump, tub seal | Tighten connections; replace cracked hoses or seals. |
| Excessive vibration | Unbalanced load, suspension | Redistribute laundry; inspect suspension rods and springs. |
Follow these steps to access internal components. Always disconnect power and water first.
Tip: Take photos during disassembly to aid reassembly.
Step-by-step guides for frequent service procedures.
Replacing Water Inlet Valve:
Replacing Drive Belt:
Replacing Lid Switch:
Replacing Pump:
Regular maintenance prevents premature failure.
CAUTION! Do not use abrasive cleaners on control panel or glass.
Common replacement parts for model 110.68102310. Use genuine Kenmore parts for best fit.
| Part Number | Description | Qty |
|---|---|---|
| WPW10206367 | Water Inlet Valve | 1 |
| WPW10206370 | Drive Motor | 1 |
| WPW10206372 | Drain Pump | 1 |
| WPW10206375 | Lid Switch Assembly | 1 |
| WPW10206378 | Drive Belt | 1 |
| WPW10206380 | Agitator Dogs (Splutch) | 1 set |
| WPW10206382 | Control Board | 1 |
| WPW10206385 | Suspension Rod | 4 |
Ordering: Contact Sears PartsDirect at 1-800-469-4663 or visit searspartsdirect.com.
Refer to the wiring diagram for electrical troubleshooting. Diagram shows connections between control board, motor, lid switch, water valve, timer, and user interface.
Key Connections:
Note: Always verify continuity with a multimeter before replacing components.
After repair, reassemble in reverse order of disassembly.
Final Verification: Machine should fill, agitate, drain, and spin without error codes.
This repair manual is for reference only. The original manufacturer's warranty may be voided by unauthorized repairs.
Disclaimer: The author and publisher are not liable for damage or injury resulting from the use of this manual. Repair at your own risk.