Kenmore 25378106890 Manual Installation

The Kenmore 25378106890 is a high-efficiency appliance requiring proper installation for optimal performance and safety. This manual provides step-by-step instructions for unpacking, preparing the installation site, connecting utilities, and final setup. Below are key sections covering safety warnings, tools required, installation procedures, initial operation, and troubleshooting.

1. Safety Precautions 2. Tools and Materials Required 3. Unpacking and Inspection 4. Site Preparation 5. Electrical Connection 6. Water Connection 7. Drain Connection 8. Leveling and Securing 9. Initial Setup and Testing 10. Specifications 11. Troubleshooting

Safety Precautions

Before installation, read all safety instructions to prevent injury or damage.

Warning	Description
Electrical Shock Hazard	Disconnect power before installation. Use properly grounded outlet.
Fire Hazard	Keep flammable materials away from unit. Ensure proper ventilation.
Crushing Hazard	Unit is heavy. Use two or more people for lifting and moving.
Water Damage	Ensure all water connections are tight and leak-free before operation.
Tip-Over Hazard	Secure unit to wall or floor as instructed to prevent tipping.

Tools and Materials Required

Gather the following tools and materials before beginning installation.

Adjustable wrench or pliers
Phillips and flat-head screwdrivers
Level
Tape measure
Pipe thread seal tape (for water connections)
Hose clamps (if not included)
Power drill (for securing brackets if needed)
Safety gloves and goggles

NOTE: All required hoses and fittings are included in the package. Verify contents before starting.

Unpacking and Inspection

Carefully unpack the unit and inspect for any damage or missing parts.

Remove all external packaging materials.
Check for visible damage to the cabinet or control panel.
Verify all parts are included: unit, inlet hoses, drain hose, installation manual, warranty card.
Remove any shipping bolts or brackets from the rear of the unit as indicated in the manual.

CAUTION! Do not discard packaging until unit is installed and tested. Save for possible returns.

Site Preparation

Prepare the installation location to ensure proper fit and operation.

Location: Level, sturdy floor near water, drain, and electrical outlets.
Clearance: Minimum 2 inches clearance at back and sides for ventilation.
Flooring: Must be level and capable of supporting unit weight (see specifications).
Environment: Avoid areas with extreme temperatures or humidity.
Access: Ensure easy access for service and maintenance.

Electrical Connection

Connect the unit to a proper electrical supply.

Ensure power is turned OFF at the circuit breaker.
Plug the unit's power cord into a dedicated, properly grounded 120V, 60Hz, 15-amp outlet.
Do not use an extension cord or adapter.
Turn power back ON at the circuit breaker.

WARNING! Improper electrical connection can cause fire or electric shock. Have a qualified electrician install outlet if needed.

Water Connection

Connect the water supply lines to the unit.

Remote: POWER, Numeric buttons, OPEN/CLOSE, INPUT, VOLUME, MUTE, RECALL, TV MENU, SETUP (DVD mode).

Turn off main water supply.
Connect inlet hoses to hot and cold water faucets (if applicable). Use thread seal tape on connections.
Connect other ends of hoses to corresponding inlet valves on the unit (marked H and C).
Hand-tighten, then use wrench for an additional half-turn. Do not overtighten.
Slowly turn on water supply and check for leaks at all connections.

Tip: Run water through hoses into a bucket first to flush out debris.

Drain Connection

Connect the drain hose to ensure proper water discharge.

Place drain hose into a standpipe or laundry sink. Maximum height: 96 inches.
Secure hose with provided clamp or bracket to prevent slipping.
Ensure no kinks or bends in the hose that could restrict flow.
If using a standpipe, insert hose no more than 6 inches deep to avoid siphoning.

WARNING! Improper drain installation can cause water overflow and property damage.

Leveling and Securing

Level the unit to prevent vibration and noise during operation.

Place level on top of unit, front to back and side to side.
Adjust front leveling feet by turning clockwise to raise, counterclockwise to lower.
Recheck level after each adjustment.
If required by local codes, secure unit to wall or floor using anti-tip bracket (included).

CAUTION! An unlevel unit may not operate correctly and can cause excessive wear.

Initial Setup and Testing

Perform initial setup and test run to verify proper installation.

Ensure all connections (power, water, drain) are secure.
Open water faucets fully.
Select a quick wash cycle and start the unit.
Check for leaks during fill cycle.
Verify unit fills, agitates, drains, and spins properly.
Listen for unusual noises or vibrations.

Reset: If error codes appear, consult troubleshooting section or disconnect power for 5 minutes.

Specifications

Model: Kenmore 25378106890
Power Requirements: 120V AC, 60Hz, 15A
Water Pressure: 20-120 psi
Dimensions (HxWxD): 42" x 27" x 28"
Weight: 180 lbs
Capacity: 4.5 cu. ft.
Water Connections: Hot & Cold inlet, 1/2" NPT
Drain Hose: 1-1/4" diameter, 6 ft length
Energy Star Certified: Yes

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't start	Power not connected	Check power cord is plugged in; verify circuit breaker is ON.
No water filling	Water supply off/hoses kinked	Turn on water faucets; straighten inlet hoses.
Water leaks	Loose connections	Tighten hose connections; check seal tape.
Excessive vibration	Unit not level	Re-level unit; ensure floor is solid.
Error code displayed	Various faults	Refer to error code chart in manual; reset power.
Poor drainage	Drain hose clogged/kinked	Clear obstruction; ensure proper drain height.

Service: For persistent issues, contact Kenmore customer service at 1-800-426-9225 or visit www.kenmore.com.