Kenmore 700 Series Washer Service Manual

The Kenmore 700 Series Washer is a high-efficiency top-loading washing machine featuring multiple wash cycles, adjustable settings, and diagnostic capabilities. This service manual provides authorized technicians with essential information for installation, operation, troubleshooting, and repair. Below are key sections covering safety, features, installation, operation, maintenance, diagnostics, and parts information.

1. Features at a Glance 2. Installation Instructions 3. Control Panel & Operation 4. Technical Specifications 5. Cycle Descriptions 6. Maintenance Procedures 7. Diagnostic Mode & Error Codes 8. Disassembly & Repair 9. Parts List & Diagrams 10. Safety Precautions 11. Troubleshooting Guide

Features at a Glance

Key components: Electronic control board, Agitator, Wash basket, Lid lock assembly, Water inlet valve, Drain pump, Motor, and Suspension system.

Feature	Description
Control Panel	Digital display with touchpad controls for cycle selection
Wash Cycles	Normal, Heavy Duty, Delicates, Quick Wash, Bulky Items
Options	Extra Rinse, Pre-Wash, Deep Fill, Delay Start
Capacity	4.5 cu. ft. stainless steel wash basket
Motor	Direct Drive motor with inverter technology
Water Levels	Auto-sensing and manual selection
Lid Lock	Safety feature preventing opening during cycle
Diagnostic Mode	Built-in self-test and error code display
Energy Star	Meets ENERGY STAR® requirements for efficiency
Noise Reduction	Sound dampening technology

Installation Instructions

Unpack and inspect all components. Ensure location meets requirements.

Remove shipping materials: Take out transit bolts and packing from drum.
Level the washer: Adjust front leveling legs; use bubble level.
Connect water supply: Attach hot and cold hoses to corresponding faucets.
Connect drain hose: Secure to standpipe or laundry tub.
Plug into dedicated 120V, 15A grounded outlet.
Run test cycle: Verify no leaks and proper operation.

WARNING! Washer is heavy; use two people for moving. Ensure all connections are secure before operation.

Control Panel & Operation

Power on washer; select desired cycle and options.

Select cycle: Press cycle button (Normal, Heavy, Delicates, etc.).
Adjust settings: Use temperature, spin speed, and soil level buttons.
Add options: Select Extra Rinse, Pre-Wash, or Delay Start as needed.
Start cycle: Press START/PAUSE; lid will lock automatically.
Monitor progress: Display shows remaining time and current stage.
Pause/stop: Press START/PAUSE to pause; press STOP to cancel.

CAUTION! Do not force open lid during operation. Wait for unlock signal.

Technical Specifications

Model Series: Kenmore 700 Series.
Type: Top-loading high-efficiency washer.
Capacity: 4.5 cubic feet.
Voltage: 120V AC, 60Hz.
Current: 15 Amps.
Water Pressure: 20-120 psi (minimum/maximum).
Dimensions (HxWxD): 43" x 27" x 28".
Weight: 180 lbs.
Motor Type: Direct Drive, inverter-controlled.
Warranty: 1-year parts and labor, 10-year motor warranty.

Cycle Descriptions

Each cycle optimized for specific fabric types and soil levels.

Normal: For everyday cotton and mixed fabrics. Medium speed spin.

Heavy Duty: For heavily soiled work clothes and jeans. High speed spin.

Delicates: Gentle agitation and spin for silk, wool, lingerie.

Quick Wash: 15-minute cycle for lightly soiled items.

Bulky Items: Extended soak and agitation for blankets, comforters.

Sanitize: Uses hot water and extended time to eliminate bacteria.

Rinse & Spin: Rinse only with final spin.

Maintenance Procedures

Regular maintenance ensures optimal performance and longevity.

Clean washer monthly: Run empty hot cycle with washer cleaner.
Inspect hoses: Check for cracks or leaks every 6 months.
Clean lint filter: Remove and rinse monthly (located near agitator).
Wipe door seal: Clean rubber gasket to prevent mold/mildew.
Level check: Verify washer remains level every 3 months.
Exterior cleaning: Use damp cloth; avoid abrasive cleaners.

Tip: Leave lid open between cycles to allow interior to dry.

Diagnostic Mode & Error Codes

Enter diagnostic mode: Unplug washer, hold START and CANCEL buttons while plugging in.

Error Code	Description	Action
F1	Water inlet timeout	Check water supply, inlet valve, pressure switch
F2	Drain timeout	Check drain hose, pump, filter for obstruction
F3	Unbalanced load	Redistribute laundry, check suspension
F4	Lid lock fault	Inspect lock mechanism and wiring
F5	Motor control fault	Check motor, control board, wiring
F6	Temperature sensor fault	Replace temperature sensor
F7	Communication error	Check control board connections

Note: Clear error codes by unplugging washer for 5 minutes.

Disassembly & Repair

For authorized technicians only. Disconnect power before servicing.

Remove top panel: Release clips at rear, slide forward.
Access control panel: Remove screws, disconnect wiring harness.
Remove front panel: Take off dispenser, remove screws.
Access tub: Remove agitator, basket, drive block.
Replace motor: Disconnect wiring, remove mounting bolts.
Replace pump: Drain residual water, disconnect hoses and wiring.

WARNING! Use proper tools. Document wire connections before disassembly.

Parts List & Diagrams

Common replacement parts for Kenmore 700 Series Washer.

Part Number	Description	Qty
WPW10304976	Water inlet valve assembly	1
WPW10227474	Drain pump	1
WPW10101010	Drive motor	1
WPW10304977	Control board	1
WPW10227475	Lid lock assembly	1
WPW10304978	Agitator	1
WPW10227476	Suspension rod	4
WPW10304979	Door seal/gasket	1

Note: Verify part numbers against serial number before ordering.

Safety Precautions

Follow all safety guidelines to prevent injury or damage.

Disconnect power before servicing.
Use proper lifting techniques; washer is heavy.
Do not bypass safety interlocks (lid lock).
Use only genuine Kenmore replacement parts.
Keep children away during operation and service.
Ensure proper grounding of electrical outlet.
Do not use extension cords.
Follow local plumbing and electrical codes.

CAUTION! Risk of electric shock. Do not expose internal components to water.

Troubleshooting Guide

Symptom	Possible Cause	Corrective Action
Washer won't start	Power issue, lid not closed	Check outlet, ensure lid fully closed, reset circuit breaker
No water filling	Water supply off, clogged inlet screens	Turn on faucets, clean inlet screens, check valve
Water won't drain	Drain hose clogged, pump issue	Check hose for kinks, clean pump filter, test pump
Excessive vibration	Unbalanced load, loose legs	Redistribute load, level and tighten legs
Loud noise during spin	Foreign object in tub, worn bearings	Check for objects, inspect tub bearings
Error codes displayed	System fault detected	Enter diagnostic mode, refer to error code chart
Clothes still wet	Spin speed too low, overloaded	Select higher spin speed, reduce load size
Leaking water	Loose connections, damaged hoses	Tighten all connections, inspect and replace hoses

Reset Procedure: Unplug washer for 5 minutes to reset control board.

Service Support: 1-800-536-6247; www.kenmore.com/service