Kenmore 790.80353310 Service Manual

The Kenmore 790.80353310 is a 30-inch electric range with a convection oven, smooth glass cooktop, digital controls, self-cleaning function, and various cooking modes. This service manual provides detailed information for qualified technicians on safety procedures, technical specifications, disassembly instructions, component testing, troubleshooting, and repair procedures. Below are key sections covering essential service information.

1. Safety Information 2. Model Specifications 3. Installation Instructions 4. Control Panel Overview 5. Disassembly Procedures 6. Component Testing 7. Error Code Diagnostics 8. Wiring Diagrams 9. Parts List & Exploded Views 10. Reassembly & Verification 11. Troubleshooting Flowcharts

Safety Information

Before servicing, disconnect power at circuit breaker or fuse. Allow components to cool. Use proper tools and personal protective equipment.

Hazard	Precaution
Electrical Shock	Verify power is disconnected with voltmeter. Discharge capacitors.
High Temperature	Allow oven and cooktop to cool completely before handling.
Sharp Edges	Wear cut-resistant gloves during disassembly.
Heavy Lifting	Use two persons for oven removal; secure range to prevent tipping.
Chemical Exposure	Ventilate area when handling oven door gasket or insulation.

Model Specifications

Model Number: 790.80353310
Type: 30" Freestanding Electric Range
Power Requirements: 240V AC, 60Hz, 40A circuit
Cooktop: Smooth glass, 4 radiant elements (6", 8", 9" dual)
Oven: Convection bake & roast, self-clean, 5.3 cu. ft. capacity
Controls: Digital touchpad with LCD display
Dimensions (HxWxD): 36.5" x 29.875" x 28.25"
Weight: 150 lbs

Installation Instructions

For initial installation or reinstallation after service.

Location: Level floor, clear of combustible materials, proper ventilation.
Electrical: Connect 4-wire cable (L1, L2, Neutral, Ground) to terminal block.
Anti-tip bracket: Secure to floor/wall per instructions.
Test: Verify all burners, oven functions, and controls operate correctly.

WARNING! Improper installation can cause fire, electric shock, or injury. Follow local codes.

Control Panel Overview

Main control board (part #W10466678) manages all user inputs and outputs.

Touchpad Functions: Power, Oven Mode (Bake, Broil, Convection, Clean), Temperature, Timer, Clock, Lock, Light.

Display Indicators: Time, temperature, active mode, error codes (F1-F10).

Behind Panel: Main control board, ribbon cables, membrane switch connections.

Disassembly Procedures

Step-by-step guide to access internal components.

Remove rear panel screws to access terminal block and wiring.
Remove control panel screws, tilt forward, disconnect ribbon cables.
Remove oven door: Open fully, lift at hinges, detach.
Remove inner door panel to access glass and gasket.
Remove oven bake/broil elements: Unplug connectors, slide out.
Remove cooktop glass: Lift after removing trim screws.

CAUTION! Label all wires and take photos before disconnection.

Component Testing

Use multimeter to test components. Disconnect power first.

Component	Test	Expected Value
Bake Element	Resistance across terminals	20-40 Ω
Broil Element	Resistance across terminals	15-30 Ω
Surface Element	Continuity between terminals	Continuity
Oven Sensor	Resistance at room temp	~1100 Ω
Thermal Fuse	Continuity	Continuity

Error Code Diagnostics

F-codes indicate specific faults. Clear by cycling power after repair.

F1: Oven temperature sensor open circuit.
F2: Oven temperature sensor short circuit.
F3: Oven over-temperature fault.
F4: Control panel communication error.
F5: Clock/display error.
F6-F10: Internal control board faults.

Wiring Diagrams

Refer to diagrams on pages 12-15 of manual for complete electrical schematics.

Key Connections: Terminal block to main board, board to elements, board to sensors, board to touchpad.

Color Codes: Black (L1), Red (L2), White (Neutral), Green/Yellow (Ground).

Parts List & Exploded Views

Common replacement parts for model 790.80353310.

Part Number	Description
W10466678	Main Control Board
W10466679	Touchpad Assembly
W10466680	Bake Element
W10466681	Broil Element
W10466682	Oven Temperature Sensor
W10466683	Cooktop Glass
W10466684	Door Gasket

Reassembly & Verification

After repair, reassemble in reverse order of disassembly.

Ensure all connectors are secure, no pinched wires.
Replace panels and screws firmly.
Restore power, run diagnostic test mode (hold Bake + Broil for 5 sec).
Test all functions: Each surface element, oven modes, temperature accuracy, self-clean initiation.

Tip: Verify oven calibration: Set to 350°F, use thermometer; adjust offset in service mode if needed.

Troubleshooting Flowcharts

Symptom	Possible Cause	Corrective Action
Oven not heating	Element failure, relay, sensor	Test element resistance; check control board output; replace sensor if F1/F2.
Cooktop element not working	Faulty element, switch, board	Swap element with known good; test infinite switch; check board connection.
Display blank	Power, fuse, board	Verify 240V at terminal block; test thermal fuse; replace main board.
Self-clean not starting	Door lock, thermostat, control	Check door latch mechanism; test lock motor; verify clean cycle selection.
Error codes displayed	Sensor, wiring, board fault	Refer to F-code list; test component; inspect wiring harness for damage.

Service Support: 1-800-422-1230; www.kenmore.com/service