Kenmore 80 Series Washer Manual

The Kenmore 80 Series Washer is a high-efficiency top-loading washing machine featuring multiple wash cycles, adjustable settings for load size and soil level, energy-saving options, and durable construction. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Agitator, Control Panel, Lid, Water Inlet Hoses, Drain Hose, Leveling Legs.

Installation

Unpack and inspect contents. Place on level floor near water supply and drain.

1. Connect water supply: Attach hot and cold hoses to corresponding faucets and washer inlet ports.
2. Connect drain hose: Secure to standpipe or laundry tub (maximum height 96 inches).
3. Level the washer: Adjust front leveling legs to prevent vibration.
4. Plug into grounded electrical outlet.

WARNING! Washer is heavy; use two people for moving. Ensure all connections are secure to prevent leaks.

First-Time Setup

Power on washer; run initial test cycle.

1. Check water connections: Turn on water faucets and check for leaks.
2. Run clean cycle: Use TUB CLEAN cycle with washer empty to remove residues.
3. Set preferences: Adjust default settings like temperature and spin speed if desired.
4. Load laundry: Do not overload; follow load size guidelines.

CAUTION! Ensure washer is level and stable before first use to prevent excessive vibration.

Specifications

• Capacity: 4.5 cubic feet.
• Voltage: 120V AC, 60Hz.
• Water Connections: Hot and cold inlet hoses.
• Cycles: Normal, Heavy Duty, Delicates, Quick Wash, Bulky Items, Rinse & Spin.
• Options: Adjustable temperature, spin speed, soil level, and extra rinse.
• Noise Level: Standard operation sound.
• Dimensions: Standard top-load washer size.
• Weight: Approximately 180 lbs.

Controls and Settings

Access settings via Control Panel. Front Panel: POWER, START/PAUSE, CYCLE SELECTION knob, OPTIONS buttons.

Cycle Selection: Turn knob to desired wash program. Options: Temperature (Hot, Warm, Cold), Spin Speed (High, Medium, Low), Soil Level (Heavy, Normal, Light), Extra Rinse (On/Off).

Display: Shows cycle time, settings, and error codes. Lid Lock: Engages during cycle for safety.

Connecting Water Supply

Hot/Cold Inlets: Connect corresponding hoses. Drain: Secure hose properly.

1. Turn off water faucets before connecting hoses.
2. Use thread seal tape on hose connections to prevent leaks.
3. Ensure drain hose is not kinked and is secured to prevent slipping.

Tip: Check hoses regularly for wear and replace every 5 years.

Using Wash Cycles

Supports various fabrics and soil levels.

1. Load laundry: Open lid, add detergent to dispenser, load clothes evenly.
2. Select cycle: Turn knob to desired program (e.g., Normal for cottons).
3. Adjust options: Set temperature, spin speed, and soil level as needed.
4. Start: Close lid, press START/PAUSE to begin cycle.
5. Pause: Press START/PAUSE to temporarily stop; open lid to add forgotten items.
6. Complete: Washer signals end of cycle; remove laundry promptly.

WARNING! Do not overload washer; balance load to prevent vibration. Use recommended detergent type.

Special Features

Delay Start: Set wash to begin later (up to 24 hours). TUB CLEAN Cycle: Runs without laundry to clean interior. Child Lock: Prevents accidental changes to settings.

Care & Cleaning

Unplug before cleaning. Wipe exterior with damp cloth; clean interior with TUB CLEAN cycle monthly.

CAUTION! Do not use abrasive cleaners; keep control panel dry. Clean lint filter regularly.

Regulatory Information

UL Listed; complies with U.S. safety standards. Energy Star certified for efficiency. Copyright © Kenmore; trademarks of Sears Brands, LLC. For support, visit www.kenmore.com or contact 1-800-469-4668.

Troubleshooting

Reset: Unplug washer for 5 minutes to reset control system.

Service: 1-800-469-4668; www.kenmore.com