Kenmore Air Conditioner Control Manual

The Kenmore Air Conditioner Control Manual provides comprehensive guidance for operating and maintaining your Kenmore air conditioning unit. It covers essential safety information, control panel functions, remote control usage, programming instructions, maintenance tips, and troubleshooting procedures to ensure optimal performance and longevity of your appliance.

1. Features at a Glance 2. Installation & Setup 3. Control Panel Overview 4. Specifications 5. Remote Control Functions 6. Operating Modes 7. Timer & Programming 8. Maintenance & Cleaning 9. Safety Information 10. Regulatory Compliance 11. Troubleshooting

Features at a Glance

Key components: Digital control panel, Remote Control, Air filter, Exhaust vent, Power cord, Temperature sensor.

Feature	Description
Digital Display	Shows temperature, mode, timer settings, and filter status
Mode Selection	Cool, Fan, Dry, Auto, and Sleep modes
Temperature Control	Adjustable from 60°F to 86°F (16°C to 30°C)
Fan Speed Control	Multiple speed settings (Low, Medium, High, Auto)
Timer Functions	24-hour programmable On/Off timer
Remote Control	Infrared remote for all functions
Air Swing	Adjustable louvers for directional air flow
Filter Alert	Indicator light for filter cleaning reminder
Energy Saver Mode	Reduces power consumption when target temperature is reached
Sleep Mode	Gradually adjusts temperature for comfortable sleeping

Installation & Setup

Unpack and inspect contents. Ensure proper window installation or placement.

Window Installation: Extend side panels, secure in window frame, lock brackets in place.
Electrical Connection: Plug into dedicated 115V/15A grounded outlet.
Initial Setup: Remove protective film from control panel, install batteries in remote.
Test Operation: Power on unit, select Cool mode, set desired temperature.

WARNING! Unit is heavy; use two people for installation. Ensure window is securely locked to prevent falling.

Control Panel Overview

Front Panel: POWER, MODE, TEMP ▲/▼, FAN SPEED, TIMER, SLEEP, SWING.

Display Indicators: Temperature, Mode icon, Fan speed, Timer status, Filter alert.

Basic Operation: Press POWER to turn on/off. Use MODE to cycle through Cool, Fan, Dry, Auto. Adjust temperature with TEMP buttons. Select fan speed with FAN button. Set timer with TIMER button. Activate sleep mode with SLEEP button. Control air direction with SWING button.

Specifications

Cooling Capacity: 8,000 BTU (for models up to 350 sq. ft.)
Power Requirements: 115V, 60Hz, 15A dedicated circuit
Energy Efficiency Ratio (EER): 12.1
Air Flow: 350 CFM (High speed)
Noise Level: ≤ 55 dB (Low speed)
Refrigerant: R-410A (eco-friendly)
Dimensions: 19" H x 24" W x 16" D
Weight: 65 lbs
Operating Temperature: 60°F to 95°F (16°C to 35°C)
Warranty: 1-year limited parts and labor

Remote Control Functions

Remote: POWER, MODE, TEMP ▲/▼, FAN, TIMER, SLEEP, SWING, LIGHT, RESET.

Remote Operation: Point remote at unit's sensor (within 20 feet). Replace batteries (2 AAA) when range decreases. LIGHT button controls display brightness. RESET restores factory settings.

Note: Remove batteries if remote not used for extended periods to prevent corrosion.

Operating Modes

Cool Mode: Cools room to set temperature. Compressor cycles on/off automatically.
Fan Mode: Circulates air without cooling. Select Low, Medium, or High speed.
Dry Mode: Reduces humidity. Fan runs at low speed.
Auto Mode: Unit automatically selects Cool or Fan based on room temperature.
Sleep Mode: Temperature gradually increases (Cool) or decreases (Heat) over 7 hours for energy savings.
Energy Saver: Fan stops when compressor cycles off, reducing energy use.

Tip: Use Auto mode for optimal energy efficiency in varying conditions.

Timer & Programming

24-Hour Timer: Program unit to turn On/Off at specific times.

Press TIMER button to enter timer setting mode.
Use TEMP ▲/▼ to set hours (0-24).
Press TIMER again to confirm.
Timer icon will flash when active.
Cancel timer by pressing TIMER until icon disappears.

Example: Set to turn on at 6:00 PM and off at 11:00 PM for evening cooling.

Maintenance & Cleaning

Unplug unit before maintenance. Clean every 2 weeks during peak season.

Filter Cleaning: Remove front grille, slide out filter. Wash with mild detergent and lukewarm water. Air dry completely before reinstalling.
Exterior Cleaning: Wipe cabinet with soft, damp cloth. Do not use abrasive cleaners.
Condenser Coils: Vacuum gently with soft brush attachment annually.
Drainage: Ensure drain holes are clear of debris.
Winter Storage: Remove from window, clean thoroughly, cover, store upright in dry location.

CAUTION! Never use water hotter than 104°F (40°C) on filters. Do not operate without filter installed.

Safety Information

Important Safety Instructions:

Plug into grounded 3-prong outlet only. Do not use extension cords.
Keep unit level during operation to ensure proper drainage.
Maintain at least 20 inches clearance on all sides for adequate airflow.
Do not block air intake or outlet vents.
Do not operate with damaged power cord or plug.
Do not insert fingers or objects into air vents.
Disconnect power before cleaning or servicing.
Install according to local building codes.

WARNING! Risk of fire or electric shock if installed or operated improperly.

Regulatory Compliance

UL Listed: Meets UL 484 room air conditioner standards. Energy Star: May qualify for Energy Star certification (check specific model). FCC Part 15: Class B digital device compliant. California Proposition 65: Contains chemicals known to cause cancer and reproductive harm. For support, visit www.kenmore.com or contact 1-800-536-6247. Copyright © 2025 Kenmore. Kenmore is a registered trademark of Sears Brands, LLC.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit not turning on	Power issue	Check outlet; ensure plug is fully inserted; test outlet with another device.
Poor cooling performance	Dirty filter/blocked vents	Clean filter; ensure 20" clearance around unit; check for closed vents in room.
Water leaking inside	Unit not level	Adjust unit to tilt slightly (1/4") to outside for proper drainage.
Loud or unusual noise	Loose parts/obstruction	Check for loose panels; remove any objects near fan; ensure unit is on stable surface.
Remote not working	Batteries/obstruction	Replace batteries; point remote at sensor; remove obstacles between remote and unit.
Error code on display	System fault	Note error code (E1-E9); consult manual; power cycle unit; call service if persistent.
Fan runs but no cool air	Temperature setting/compressor	Set temperature below room temp; wait 3 minutes for compressor to restart; check for tripped circuit breaker.
Ice forming on coils	Low temperature/dirty filter	Set temperature higher; clean filter; ensure adequate airflow.

Reset Procedure: Unplug unit for 5 minutes, then plug back in to reset control board.

Service: 1-800-536-6247; www.kenmore.com