Kenmore All Floors Vacuum Owner's Manual

The Kenmore All Floors Vacuum is a versatile upright vacuum cleaner designed for use on carpets, hard floors, and area rugs. It features a powerful motor, adjustable height settings, a HEPA filtration system, onboard tools, a retractable cord, and a large-capacity dust cup. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Using Onboard Tools 7. Maintenance & Cleaning 8. Filtration System 9. Care & Storage 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Upright vacuum body, motorized brush roll, adjustable handle, dust cup with release, HEPA filter, onboard tool storage, retractable power cord, and floor height adjustment dial.

Feature	Description
Motorized Brush Roll	Automatically adjusts for carpets and hard floors
Height Adjustment Dial	5 settings for different carpet pile heights
HEPA Filtration System	Traps 99.97% of dust and allergens
Large Capacity Dust Cup	Easy-empty container with one-touch release
Onboard Tools	Crevice tool, upholstery brush, and dusting brush
Retractable Power Cord	25-foot cord with automatic rewind
Headlight	LED light illuminates dark areas
Washable Filters	Main and pre-motor filters are reusable
Edge Cleaning	Bristles extend to clean along baseboards
Handle Release	Lets vacuum lie flat for under furniture cleaning

Assembly & Setup

Unpack and inspect all parts. Assemble before first use.

Attach handle: Insert handle into body until it clicks into place.
Install tools: Snap crevice tool and brush into onboard storage clips.
Check filters: Ensure HEPA and pre-motor filters are properly seated.
Unwind cord: Plug into grounded outlet; ensure cord is fully extended.

WARNING! Do not use if any parts are damaged. Keep hands away from brush roll during operation.

First-Time Use

Before vacuuming, perform these steps.

Adjust height: Turn dial to match floor surface (low for hard floors, high for thick carpets).
Test suction: Turn on power switch; listen for consistent motor sound.
Empty dust cup: Ensure it is empty before first use.
Practice cord retraction: Press retract button to rewind cord safely.

CAUTION! Keep vacuum upright during use. Do not vacuum wet spills or large debris.

Specifications

Model Type: Upright vacuum cleaner.
Motor Power: 12 amp motor.
Cord Length: 25 feet retractable.
Dust Cup Capacity: 2.0 liters.
Filtration: HEPA filter with washable pre-motor filter.
Brush Roll: Auto-adjusting, on/off switch for hard floors.
Weight: 15 lbs.
Height Settings: 5-position dial.
Warranty: 1-year limited warranty.
Power Source: 120V AC, 60Hz.

Controls and Settings

Main controls located on handle and body.

Handle: Power switch, brush roll on/off button, cord retract button.

Body: Height adjustment dial, dust cup release button, filter access door.

Operation: Turn power switch to ON; adjust height dial as needed. Use brush roll on/off for hard floors (OFF) or carpets (ON). Press cord retract button to rewind cord; guide cord to prevent tangling.

Using Onboard Tools

Tools stored on vacuum for above-floor cleaning.

Remove tool: Pull crevice tool or brush from storage clip.
Attach hose: Pull hose from rear of vacuum; insert tool into end.
Select setting: For upholstery, use brush tool; for tight spaces, use crevice tool.
Clean: Turn on vacuum; move tool over surface.
Return tools: Store tools in clips after use.

Tip: Turn off brush roll when using tools for above-floor cleaning.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

Empty dust cup: Press release button; empty contents into trash.
Clean brush roll: Turn off and unplug; remove debris from brush roll ends.
Check for blockages: Inspect hose, nozzle, and air passages if suction decreases.
Replace filters: HEPA filter every 6-12 months; pre-motor filter every 3 months.

WARNING! Always unplug vacuum before performing maintenance.

Filtration System

HEPA filtration traps fine particles.

Filters: Pre-motor filter (washable) and HEPA filter (replaceable). Wash pre-motor filter every month under cold water; air dry completely before reinstalling. Replace HEPA filter when indicated or every 6-12 months. Order replacement filters from Kenmore or authorized dealers.

Care & Storage

Store vacuum in a dry, cool place.

After use: Empty dust cup, rewind cord, wipe exterior with dry cloth. Store upright; do not hang by hose. Keep away from heat sources and direct sunlight.

CAUTION! Do not store with wet filters; ensure all parts are dry.

Regulatory Information

UL listed; complies with U.S. safety standards. Copyright © Kenmore; trademarks of Kenmore, Sears Brands, LLC. For support, visit www.kenmore.com or contact 1-800-469-4668. This product is for household use only.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Vacuum won't turn on	Power cord/outlet	Check plug; try different outlet; ensure power switch is ON.
Loss of suction	Full dust cup/clog	Empty dust cup; check hose and nozzle for blockages.
Brush roll not spinning	Debris/switch	Clear debris from brush roll; ensure brush roll switch is ON for carpets.
Overheating	Clogged filter/full cup	Clean filters; empty dust cup; let vacuum cool for 30 minutes.
Cord not retracting	Tangled/obstruction	Unplug; manually rewind cord; check for obstructions in reel.
Unusual noise	Foreign object	Turn off and unplug; inspect brush roll and hose for objects.

Reset: Unplug for 10 minutes; plug back in if motor overheats.

Service: 1-800-469-4668; www.kenmore.com