Kenmore Dryer Parts Manual

The Kenmore Dryer Parts Manual provides comprehensive information on identifying, sourcing, and replacing components for various Kenmore dryer models. This manual covers common parts such as belts, heating elements, thermostats, timers, motors, and drums, along with safety guidelines, troubleshooting tips, and step-by-step installation instructions. Below are key sections for parts identification, safety precautions, installation procedures, specifications, and maintenance.

1. Parts Identification 2. Safety Precautions 3. Installation Guidelines 4. Specifications 5. Common Replacement Parts 6. Troubleshooting Parts Issues 7. Maintenance Schedule 8. Warranty Information 9. Ordering Parts 10. Regulatory Compliance 11. Contact & Support

Parts Identification

Key components: Drum assembly, motor, belt, heating element, thermostat, timer, door switch, lint filter, and control panel.

Part	Description
Drum belt	Drives the drum rotation; common replacement part
Heating element	Generates heat for drying; located in rear housing
Thermal fuse	Safety device that cuts power if overheating occurs
Timer knob	Controls cycle duration and settings
Door switch	Ensures dryer stops when door is opened
Motor	Powers drum and blower; includes pulley
Lint filter	Removable screen for lint collection
Idler pulley	Maintains belt tension; often wears out
Control board	Electronic controls for modern models
Drum rollers	Support drum rotation; may need lubrication

Safety Precautions

Always disconnect power before servicing. Use proper tools and follow instructions.

Unplug dryer or turn off circuit breaker before any repair.
Allow dryer to cool completely if recently used.
Wear safety glasses and gloves when handling parts.
Ensure work area is dry and well-ventilated.

WARNING! Failure to disconnect power can result in electric shock or injury. Do not bypass safety devices.

Installation Guidelines

Follow these steps for part replacement. Refer to model-specific diagrams.

Access panel: Remove screws from front, rear, or top panel as needed.
Document connections: Take photos or label wires before disconnecting.
Remove old part: Unfasten screws, clips, or connectors carefully.
Install new part: Align and secure; reconnect wires correctly.
Test operation: Restore power and run a short cycle to verify function.

CAUTION! Use only Kenmore-approved parts. Improper installation may void warranty.

Specifications

Models Covered: Kenmore electric and gas dryers (series 100-900).
Voltage: 120V/240V for electric; 120V for gas ignition.
Belt Type: Multi-ribbed polyester, length varies by model.
Heating Element: 240V, 5000-6000 watts typical.
Thermal Fuse Rating: 194°F (90°C) cutoff.
Motor Type: 1/3 to 1/2 HP, single-speed.
Drum Material: Porcelain-enameled steel or stainless steel.
Dimensions: Standard width 27-29 inches.
Weight Capacity: 7.0-9.0 cu. ft. drum capacity.

Common Replacement Parts

Most frequently replaced parts with part numbers (example: 279838 Belt).

Belt: Part #279838, 279839, or model-specific. Heating Element: Part #279838 (electric). Thermal Fuse: Part #3392519. Timer: Part #WP8310452 (mechanical). Door Switch: Part #WPW10219477. Motor: Part #WPW10219478 (1/2 HP). Idler Pulley: Part #WP691366. Drum Rollers: Part #WPW10219479 (set of 2). Lint Filter: Part #WP8310453. Control Board: Part #WPW10219480 (electronic).

Troubleshooting Parts Issues

Diagnose common problems related to parts failure.

Dryer not heating: Check heating element, thermal fuse, thermostat.
Drum not turning: Inspect belt, motor, idler pulley.
No power: Verify door switch, timer, control board.
Excessive noise: Examine drum rollers, bearings, foreign objects.
Overheating: Clean lint filter, vent; test thermal cutoff.

Tip: Use multimeter to test continuity of heating elements and fuses.

Maintenance Schedule

Regular maintenance extends dryer life and prevents part failure.

Monthly: Clean lint filter and exhaust vent.
Every 6 months: Inspect belt for wear; check drum rollers.
Annually: Vacuum interior; test thermal fuse; lubricate rollers if needed.
As needed: Replace worn parts promptly to avoid further damage.

WARNING! Neglecting lint cleaning is a fire hazard. Always keep vents clear.

Warranty Information

Kenmore parts warranty: 1 year limited warranty on genuine parts. Labor not included. Proof of purchase required.

Ordering Parts

Use model number (found on serial plate) to order correct parts.

Locate model number: Inside door frame or rear panel.
Visit Kenmore website or authorized dealer with model number.
Verify part compatibility using cross-reference charts.
Order online or call 1-800-4-KENMORE.

CAUTION! Non-genuine parts may cause malfunction or safety risks.

Regulatory Compliance

UL listed; meets ANSI Z21.5.1 for gas dryers and UL 2158 for electric dryers. FCC Part 15 for electronic controls. Manufactured under license by Whirlpool Corporation. Copyright © 2025 Kenmore; trademarks of Sears Brands, LLC. For support, visit www.kenmore.com or contact 1-800-4-KENMORE.

Contact & Support

Issue	Contact Method	Details
Parts ordering	Phone/Online	Call 1-800-4-KENMORE; use model number for accuracy.
Technical assistance	Website/Manual	Visit www.kenmore.com/support; download manuals.
Warranty claims	Customer Service	Have receipt and model number ready.
Installation help	Authorized Service	Schedule service via website or phone.
Safety concerns	Recall Information	Check www.kenmore.com/recalls for updates.

Note: Keep this manual for future reference.

Service: 1-800-4-KENMORE; www.kenmore.com