Kenmore Electric Dryer Manual

The Kenmore Electric Dryer is a household appliance designed for efficient drying of laundry. It features multiple drying cycles, temperature settings, and safety mechanisms. This manual covers safety instructions, installation, operation, maintenance, and troubleshooting for your Kenmore Electric Dryer. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Power 7. Operating the Dryer 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Drying drum, control panel, lint filter, exhaust vent, power cord, and door with safety switch.

Feature	Description
Drying Cycles	Multiple cycles including Normal, Delicates, Heavy Duty, and Air Fluff
Temperature Settings	Adjustable heat levels (High, Medium, Low, No Heat)
Lint Filter	Removable filter for easy cleaning
Door Safety Switch	Stops dryer when door is opened
Control Panel	Digital display and push-button controls
Exhaust Vent	Connects to external venting system
Power Cord	Standard 3-prong plug for 240V outlet
Start/Pause Button	Initiates or pauses drying cycle
Cycle Selector Knob	Rotates to choose drying cycle
Signal Alert	Audible alert when cycle is complete

Installation

Unpack and inspect contents. Place on level floor near power outlet and venting.

Position dryer: Ensure at least 1 inch clearance on all sides for ventilation.
Connect exhaust vent: Attach flexible or rigid duct to dryer exhaust port and route to outside.
Check power requirements: Verify 240V, 30-amp dedicated circuit.
Plug into outlet: Ensure plug is fully inserted into grounded outlet.

WARNING! Dryer is heavy; use two people to move. Ensure venting is secure to prevent fire hazard.

First-Time Setup

Before first use, complete these steps.

Remove shipping materials: Check drum and interior for packing blocks or tape.
Clean lint filter: Remove and rinse under water, dry completely before replacing.
Test run: Run a short cycle with damp towels to remove any manufacturing residues.
Set preferences: Adjust signal volume and display brightness if available.

CAUTION! Do not operate without lint filter installed. Ensure door closes securely.

Specifications

Type: Electric Dryer.
Capacity: 7.0 cubic feet.
Power Requirements: 240V AC, 30A, 60Hz.
Drum Material: Porcelain enamel.
Control Type: Electronic with digital display.
Cycles: Normal, Permanent Press, Delicates, Heavy Duty, Air Fluff, Timed Dry.
Temperature Settings: High, Medium, Low, No Heat.
Dimensions (HxWxD): 43" x 27" x 29".
Weight: 130 lbs.

Controls and Settings

Access settings via control panel. Front Panel: START/PAUSE, CYCLE SELECTOR, TEMPERATURE, OPTIONS.

Control Panel: START/PAUSE, Cycle Selector Knob, Temperature buttons, Signal button, Display (shows time remaining, cycle status).

Cycle Selection: Turn knob to desired cycle (Normal, Permanent Press, Delicates, etc.). Temperature: Press TEMP to cycle through High, Medium, Low, No Heat. Options: Press OPTIONS for Wrinkle Shield, Signal volume, End of Cycle signal. Settings: Display brightness, language (default ENGLISH), factory reset.

Connecting to Power

Requires dedicated 240V, 30-amp circuit with proper grounding.

Turn off circuit breaker for dryer outlet.
Plug dryer cord into matching 3-prong 240V outlet.
Ensure plug is fully inserted and secure.
Turn circuit breaker back on.

Tip: Have a qualified electrician install outlet if not already present. Do not use extension cord.

Operating the Dryer

Follow these steps for normal operation.

Load laundry: Do not overload; leave space for items to tumble freely.
Select cycle: Turn knob to desired cycle (e.g., Normal for cotton).
Set temperature: Press TEMP to choose heat level.
Start dryer: Press START/PAUSE; display shows time remaining.
Pause/stop: Press START/PAUSE to pause; open door to stop immediately.
End of cycle: Signal sounds; remove laundry promptly to reduce wrinkling.
Clean lint filter: Remove and clean lint filter after every cycle.

WARNING! Do not dry items that have been in contact with flammable substances. Do not block vent.

Safety Features

Thermal Fuse: Prevents overheating. Door Switch: Stops drum rotation when door is opened. Lint Filter Alert: Reminder to clean filter. Child Lock: Locks control panel to prevent accidental changes.

Care & Cleaning

Unplug before cleaning. Wipe exterior with damp cloth; clean lint filter after each use. Inspect and clean exhaust vent annually.

CAUTION! Do not use abrasive cleaners. Ensure dryer is cool before cleaning interior.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
Dryer won't start	Door open/power	Close door securely; check circuit breaker; ensure plug is fully inserted.
No heat	Settings/thermal fuse	Check temperature setting (not on "No Heat"); verify thermal fuse; call service if needed.
Long drying times	Lint/venting	Clean lint filter; check exhaust vent for blockages; do not overload.
Unusual noise	Foreign objects	Check drum for coins, buttons; ensure dryer is level on floor.
Error code on display	Various faults	Refer to error code chart in manual; reset by unplugging for 5 minutes.

Reset: Unplug dryer for 5 minutes to reset electronic controls.

Service: 1-800-469-4668; www.kenmore.com