Kenmore Electric Range Model 790 Parts Manual

The Kenmore Electric Range Model 790 is a freestanding electric range featuring a self-cleaning oven, smooth glass cooktop, digital clock and timer, infinite heat control surface elements, and a storage drawer. This manual provides detailed parts identification, replacement procedures, and ordering information to assist with maintenance and repair. Below are key sections for parts overview, installation, replacement guides, specifications, and troubleshooting.

1. Parts Overview 2. Installation & Safety 3. Cooktop Components 4. Oven Components 5. Control Panel & Electrical 6. Replacement Procedures 7. Specifications 8. Care & Maintenance 9. Regulatory Information 10. Troubleshooting

Parts Overview

Key components: Glass cooktop assembly, surface heating elements, oven bake and broil elements, oven door assembly, control panel, clock/timer module, infinite heat switches, storage drawer, and wiring harness.

Part NumberDescription
790-001Glass Cooktop Assembly
790-002Surface Heating Element (8-inch)
790-003Surface Heating Element (6-inch)
790-004Oven Bake Element
790-005Oven Broil Element
790-006Oven Door Assembly
790-007Control Panel with Clock/Timer
790-008Infinite Heat Control Switch
790-009Storage Drawer Assembly
790-010Main Wiring Harness

Installation & Safety

Unpack and inspect all parts. Ensure proper electrical connection.

  1. Electrical Connection: Requires 240V, 60Hz dedicated circuit with proper grounding.
  2. Positioning: Place range on level floor, allowing clearance at sides and rear.
  3. Anti-tip Bracket: Install provided bracket to secure range and prevent tipping.
  4. Initial Test: After installation, test all surface elements and oven functions.

WARNING! Disconnect power at circuit breaker before installation or servicing. Range is heavy; use two people for handling.

Cooktop Components

Components located under the glass cooktop surface.

  1. Surface Elements: Four radiant heating elements (two 8-inch, two 6-inch).
  2. Infinite Heat Switches: Control knobs for variable temperature settings.
  3. Element Sockets: Connect elements to power supply.
  4. Glass Surface: Tempered glass, clean with approved cleaners only.

CAUTION! Allow cooktop to cool completely before cleaning or servicing.

Oven Components

Control Panel & Electrical

Front control panel includes clock, timer, oven controls, and indicator lights.

Control Components: Clock/Timer Module, Oven Selector Switch, Temperature Knob, Self-Clean Button, Indicator Lights (Oven On, Clean).

Electrical: Main power cord (4-wire), terminal block, oven selector switch wiring, infinite switch wiring for surface elements, thermostat wiring, door switch wiring for self-clean safety.

Replacement Procedures

General steps for common part replacements. Always disconnect power first.

  1. Surface Element: Lift old element, disconnect wires, connect new element, press into place.
  2. Oven Bake/Broil Element: Remove oven racks, unscrew element brackets, disconnect wires, install new element.
  3. Oven Door: Open door fully, lift and disengage hinges, reverse to install new door.
  4. Control Knob: Pull straight off shaft, align new knob and push on.

Tip: Take photos of wiring before disconnecting for reference during reassembly.

Specifications

Supports standard cookware and oven use.

  1. Power Requirements: 240V AC, 60Hz, 40 Amp circuit.
  2. Cooktop: Four radiant elements (Total 6600 Watts).
  3. Oven: Self-cleaning, 5.0 cu. ft. capacity, Bake: 3400W, Broil: 3000W.
  4. Controls: Infinite heat surface controls, mechanical oven thermostat.
  5. Clock/Timer: 60-minute timer with audible signal.
  6. Dimensions: 30" Width, 47" Height (with backsplash), 28" Depth.
  7. Finish: White porcelain on steel.

WARNING! Use only manufacturer-specified replacement parts.

Care & Maintenance

Self-Cleaning Oven: Engage lock, run 2-3 hour cycle. Cooktop: Clean with ceramic glass cleaner. Storage Drawer: Remove and wash with mild detergent.

Regulatory Information

UL Listed. Complies with ANSI Z21.1 standards. Manufactured for Sears Brands, LLC. Copyright © Kenmore. For parts ordering and technical support, visit www.searspartsdirect.com or contact 1-800-469-4663.

Troubleshooting

SymptomPossible CauseCorrective Action
Surface element not heatingFaulty element or switchTest element for continuity; replace if open; check infinite switch.
Oven not heatingBake/broil element failureCheck elements for breaks; replace faulty element; verify thermostat.
Clock/timer not workingPower or module failureCheck power to range; replace clock/timer module if needed.
Self-clean not engagingDoor not latchedEnsure door is fully closed and latched; check door switch.
Uneven cookingOven temperature calibrationCalibrate oven thermostat using adjustment screw behind knob.

Reset: Turn power off at breaker for 1 minute to reset electronic controls.

Service: 1-800-469-4663; www.searspartsdirect.com

Kenmore Electric Range Model 790 Parts Manual © - All Rights Reserved 2025