Kenmore Elegance Vacuum Manual

The Kenmore Elegance is a high-performance upright vacuum cleaner featuring powerful suction, multi-surface cleaning capabilities, HEPA filtration system, adjustable height settings, motorized brush roll, large-capacity dust cup, onboard tool storage, and a variety of accessories for comprehensive home cleaning. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Using Accessories 7. Cleaning Different Surfaces 8. Maintenance & Care 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Power head with motorized brush, Handle with controls, Dust cup with HEPA filter, Hose assembly, Onboard tool caddy, Power cord, Various cleaning attachments.

Feature	Description
Motorized Brush Roll	Deep cleans carpets and agitates embedded dirt
HEPA Filtration System	Captures 99.97% of dust and allergens
Adjustable Height Settings	5 positions for different carpet pile heights
Large Capacity Dust Cup	Easy-empty container for less frequent emptying
Onboard Tool Storage	Convenient storage for crevice tool and upholstery brush
Multi-Surface Cleaning	Switch between carpets, hard floors, and delicate surfaces
Powerful Suction	High-performance motor for thorough cleaning
Edge Cleaning	Special design cleans along baseboards and edges
Wand Release	Quick-release for above-floor cleaning
Headlight	Illuminates dark areas under furniture

Assembly & Setup

Unpack and inspect all contents. Assemble following these steps.

Attach handle: Insert handle into vacuum body until it clicks securely.
Install hose: Connect hose to vacuum body and wand attachment points.
Attach tools: Place crevice tool and upholstery brush in onboard caddy.
Check filters: Ensure HEPA filter and pre-motor filter are properly installed.
Plug into electrical outlet.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Use

Before first use, perform initial setup and testing.

Adjust height: Set appropriate height for your flooring (lowest setting for bare floors).
Test suction: Turn on vacuum and verify proper operation.
Check brush roll: Ensure brush roll rotates freely without obstruction.
Empty dust cup: Empty even if new to ensure optimal performance.
Familiarize with controls: Practice using power switch, brush roll on/off, and height adjustment.

CAUTION! Keep hair, loose clothing, and cords away from brush roll during operation.

Specifications

Model: Kenmore Elegance Series Upright Vacuum
Motor: High-performance 12 amp motor
Filtration: HEPA filtration system
Cord Length: 25-foot power cord
Dust Cup Capacity: 1.5 liters
Height Settings: 5 adjustable positions
Brush Roll: Motorized with on/off control
Weight: 18 pounds
Warranty: 1-year limited warranty
Power Source: 120V AC, 60Hz

Controls and Settings

Main controls located on handle: Power switch, Brush roll on/off, Height adjustment lever.

Power Switch: Turns vacuum on/off. Brush Roll Control: Engages/disengages motorized brush for different surfaces. Height Adjustment: 5 positions (1-lowest for hard floors, 5-highest for thick carpets). Wand Release: Button to detach wand for above-floor cleaning. Dust Cup Release: Lever to remove dust cup for emptying.

Settings: Adjust height based on surface type. Use brush roll on for carpets, off for hard floors and delicate rugs. Utilize edge cleaning feature for baseboards.

Using Accessories

Accessories included: Crevice tool, Upholstery brush, Dusting brush, Extension wand.

Detach wand: Press wand release button and pull wand from vacuum.
Attach tool: Connect desired tool to end of wand or hose.
Select suction: Use appropriate suction setting for accessory.
Clean: Use tool for specific cleaning tasks (crevices, upholstery, etc.).
Return tools: Store tools in onboard caddy when not in use.

Tip: For above-floor cleaning, turn off brush roll to prevent damage to furniture.

Cleaning Different Surfaces

Optimize cleaning for various floor types and surfaces.

Bare floors/Hard surfaces: Set height to lowest position, turn brush roll off.
Low-pile carpets: Use height setting 2 or 3 with brush roll on.
Medium-pile carpets: Use height setting 3 or 4 with brush roll on.
High-pile/Plush carpets: Use highest setting (5) with brush roll on.
Area rugs/Delicates: Turn brush roll off to prevent damage.
Stairs: Use hose and attachments with wand detached.
Upholstery: Use upholstery tool with moderate suction.
Blinds/Drapes: Use dusting brush on low suction setting.

WARNING! Always turn off and unplug vacuum before changing settings or attachments.

Maintenance & Care

Regular maintenance ensures optimal performance and longevity.

Empty dust cup: Empty when full or after each use.
Clean filters: Wash pre-motor filter monthly; replace HEPA filter every 6-12 months.
Check brush roll: Remove tangled hair and debris regularly.
Inspect hose: Clear any obstructions in hose and wand.
Check belt: Replace drive belt if worn or broken (approximately yearly).
Clean exterior: Wipe with damp cloth; avoid water near electrical components.

CAUTION! Unplug vacuum before performing any maintenance. Allow filters to dry completely before reinstalling.

Regulatory Information

UL Listed: Certified for safety in the United States and Canada. Energy efficient design. Copyright © Kenmore; trademarks of Sears Brands, LLC. For support, visit www.kenmore.com or contact 1-800-469-4668. This product meets applicable federal standards.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Loss of suction	Full dust cup or clog	Empty dust cup; check hose and wand for obstructions; clean filters.
Brush roll not spinning	Tangled debris or broken belt	Clear hair and debris from brush roll; replace drive belt if necessary.
Vacuum won't turn on	Power cord or outlet issue	Check power cord connection; try different outlet; check circuit breaker.
Unusual noise	Foreign object in brush roll or fan	Turn off immediately; check for and remove obstructions.
Vacuum difficult to push	Height setting too low	Adjust to higher setting for carpet type.
Dust escaping	Filter not installed properly	Ensure all filters are correctly seated and clean.
Hose detaches	Connection not secure	Push hose firmly into connection points until it clicks.

Reset: Unplug for 10 minutes if vacuum overheats and shuts off.

Service: 1-800-469-4668; www.kenmore.com