Kenmore Elite 795 Refrigerator Service Manual

The Kenmore Elite 795 is a high-performance French door refrigerator featuring advanced cooling technology, dual evaporators, ice and water dispensers, adjustable shelving, LED lighting, and energy-efficient operation. This service manual provides comprehensive information for authorized technicians, including safety procedures, technical specifications, component locations, diagnostic troubleshooting, repair instructions, and maintenance schedules for the 795 series models.

Safety Information & Precautions

Critical safety warnings for technicians before servicing the Kenmore Elite 795 refrigerator.

Model Specifications & Features

Technical specifications and key features of the Kenmore Elite 795 series.

• Model Series: 795.70xxx, 795.71xxx, 795.72xxx
• Dimensions (HxWxD): 69.875" x 35.75" x 34.5"
• Capacity: 27.5 cu. ft. total (Fresh Food: 18.3 cu. ft., Freezer: 9.2 cu. ft.)
• Refrigerant: R-600a (Isobutane)
• Defrost System: Adaptive Defrost with dual evaporators
• Compressor: Variable Speed Inverter Compressor
• Electrical: 115 VAC, 60 Hz, 7.5 Amps
• Water Filter: EveryDrop® Filter 4 (EDR4RXD1)
• Features: TwinChill™ evaporators, Turbo Cool setting, Sabbath mode, external temperature display, spill-proof shelves.

Component Identification & Access

Locations of major components and instructions for accessing serviceable parts.

1. Control Board: Behind the top grille. Remove grille by pulling forward.
2. Compressor & Condenser: Access panel at rear bottom of unit.
3. Evaporator Fans: Fresh food fan behind rear panel in refrigerator compartment. Freezer fan behind rear panel in freezer.
4. Water Inlet Valve: Located at rear, bottom left behind access panel.
5. Ice Maker Assembly: In the upper left freezer compartment.
6. Door Switches & Sensors: Behind door trim and liner.

WARNING! Always disconnect power and remove food/ shelves before accessing internal components.

Electrical System & Wiring Diagrams

Circuit descriptions and wiring schematics for troubleshooting electrical faults.

Main Components: Main Control Board (Part # W10807810), User Interface Board, Inverter Compressor Board, Defrost Heaters, Temperature Sensors (Fresh Food, Freezer, Evaporator), Damper Motor, Ice Maker, Water Valve, Fans (Evaporator, Condenser).

Diagnostic Mode: Enter by pressing "Light" and "Ice Type" buttons simultaneously for 3 seconds. Use "+" and "-" to scroll through test modes.

Refrigeration System Overview

Sealed system components and refrigerant flow path.

1. Compressor: Variable speed, lubricated with POE oil.
2. Condenser: Serpentine coil with forced-air fan.
3. Capillary Tube: Metering device for each evaporator.
4. Evaporators: Separate coils for fresh food and freezer sections.
5. Accumulator: Prevents liquid refrigerant from entering compressor.
6. Filter-Drier: Removes moisture and contaminants.

CAUTION! The system uses R-600a, a flammable refrigerant. No brazing or hot work without proper purging.

Control System & User Interface

Operation of the electronic control system and display panel.

Display Panel Controls: Temperature Set (Fridge/Freezer), Turbo Cool, Turbo Freeze, Ice Maker On/Off, Filter Reset, Lock, Sabbath Mode.

Sensor Functions: - Fresh Food Sensor: Controls damper opening and compressor speed. - Freezer Sensor: Controls defrost cycle and freezer fan. - Evaporator Sensor: Monitors coil temperature for defrost termination.

Diagnostic Error Codes

Fault codes displayed on the control panel or accessed via diagnostic mode.

Disassembly & Repair Procedures

Step-by-step instructions for common repairs.

1. Replacing Water Filter: Turn filter 90° counterclockwise, pull out. Insert new filter, turn clockwise until it stops.
2. Evaporator Fan Replacement (Freezer): Remove rear panel, disconnect wire harness, remove fan mounting screws.
3. Defrost Heater Replacement: Remove freezer evaporator cover, disconnect heater terminals, remove brackets.
4. Door Gasket Replacement: Peel back gasket from channel, starting at a corner. Insert new gasket into channel around entire door.
5. Ice Maker Assembly Replacement: Remove screws securing unit, disconnect water fill tube and electrical connector.

Performance Testing & Calibration

Verifying system operation after repair.

• Temperature Pull-Down: Unit should reach 37°F in fresh food and 0°F in freezer within 24 hours of start-up.
• Compressor Run Test: In diagnostic mode, force compressor on and verify operation at various speeds.
• Defrost Cycle Test: Initiate defrost and verify heater energizes for ~20-30 minutes until termination temperature reached.
• Damper Operation: Verify damper opens/closes based on fresh food temperature setting.
• Dispenser Test: Check water flow rate (approx. 7 oz. in 10 sec) and ice production cycle.

Preventive Maintenance

Recommended maintenance schedule to ensure optimal performance and longevity.

1. Every 6 Months: Clean condenser coils with brush or vacuum.
2. Every 6 Months: Inspect and clean door gaskets with mild soapy water.
3. Every 6 Months: Check water line connections for leaks.
4. As Needed: Defrost freezer if ice buildup exceeds 1/4 inch on evaporator.
5. As Needed: Clean interior with baking soda solution (2 tbsp per quart water).

CAUTION! Do not use sharp tools to remove ice from evaporator. Use a plastic scraper only.

Parts List & Exploded Views

Key replacement parts and their part numbers for the Kenmore Elite 795.

Ordering: Use exact part number. Verify model number (795.xxxxx) before ordering.

Service Support: 1-800-422-1230 (Sears Parts Direct) or visit searspartsdirect.com