Kenmore Elite Dryer Parts Manual
The Kenmore Elite Dryer Parts Manual provides comprehensive information on identifying, ordering, and replacing components for your Kenmore Elite dryer. This guide covers common replacement parts such as belts, heating elements, thermostats, rollers, and drums, along with part numbers, diagrams, safety precautions, and step-by-step installation instructions. Below are key sections for safety, part identification, ordering, installation, troubleshooting, and maintenance.
Safety Precautions
Before servicing your dryer, always follow these safety guidelines to prevent injury or damage.
- Disconnect Power: Unplug dryer from electrical outlet or turn off circuit breaker.
- Allow Cooling: Let dryer cool completely before handling internal parts.
- Use Proper Tools: Employ appropriate screwdrivers, wrenches, and multimeter.
- Grounding: Ensure dryer is properly grounded to avoid electrical shock.
- Ventilation: Work in a well-ventilated area if inspecting heating elements.
WARNING! Failure to disconnect power may result in severe electrical shock. Never bypass safety interlocks.
Parts Identification & Diagrams
Refer to the exploded-view diagrams to locate parts within your dryer model.
| Diagram Section | Key Components |
|---|
| Cabinet & Front Panel | Door latch, hinges, control panel, knobs |
| Drum Assembly | Drum, front/rear glides, seal, baffles |
| Drive System | Motor, drive belt, idler pulley, tensioner |
| Heating System | Heating element, thermostats, thermal fuse, igniter (gas models) |
| Venting System | Blower wheel, lint screen housing, duct |
| Electrical System | Timer, switches, sensors, wiring harness |
Note: Diagrams are model-specific; confirm your model number (e.g., 110.XXXXXX) before ordering.
Common Replacement Parts
List of frequently replaced parts with typical part numbers.
- Drive Belt: Part #279640 - V-shaped belt for drum rotation.
- Heating Element: Part #279838 - For electric dryer heating.
- Thermal Fuse: Part #279816 - Safety cut-off for overheating.
- High-Limit Thermostat: Part #279815 - Regulates temperature.
- Drum Support Rollers: Part #279827 - Supports drum rotation.
- Idler Pulley: Part #279829 - Maintains belt tension.
- Door Switch: Part #279839 - Interlock for door safety.
- Lint Screen: Part #279841 - Removable lint filter.
- Motor: Part #279835 - Drive motor assembly.
- Start Switch: Part #279837 - Push-to-start button.
Note: Part numbers may vary by model; verify compatibility.
Ordering Parts
Steps to order genuine Kenmore Elite dryer parts.
- Locate Model Number: Find label inside door or on back panel.
- Use Parts Diagram: Identify part number from manual diagram.
- Order Sources: Kenmore website, authorized dealers, appliance parts stores.
- Provide Information: Model number, part number, description.
- Verify Shipping: Confirm part matches your dryer model.
Tip: Keep receipt and packaging for warranty claims.
Installation Instructions
General steps for replacing common parts; refer to specific part instructions.
- Drive Belt Replacement:
- Unplug dryer, remove top panel.
- Release tension on idler pulley, remove old belt.
- Route new belt around motor pulley, drum, and idler.
- Re-tension belt, reassemble panels.
- Heating Element Replacement:
- Disconnect power, remove rear panel.
- Disconnect wires from element terminals.
- Remove mounting screws, install new element.
- Reconnect wires, replace panel, test operation.
- Thermal Fuse Replacement:
- Locate fuse on blower housing or heating assembly.
- Disconnect wires, remove fuse.
- Install new fuse, reconnect wires.
CAUTION! Ensure all connections are secure; test dryer before regular use.
Troubleshooting Common Issues
| Symptom | Possible Cause | Corrective Action |
|---|
| Dryer not heating | Heating element, thermal fuse, thermostat | Test element for continuity; replace if open; check fuse and thermostat. |
| Drum not turning | Drive belt, idler pulley, motor | Inspect belt for wear; replace if broken; check pulley and motor. |
| Noisy operation | Worn rollers, foreign objects, blower wheel | Replace drum support rollers; remove debris; inspect blower. |
| Dryer not starting | Door switch, start switch, timer | Test door switch continuity; replace if faulty; check start switch and timer. |
| Overheating | Blocked vent, faulty thermostat | Clean lint from vent duct; replace high-limit thermostat. |
Note: Use multimeter for electrical testing; disconnect power first.
Maintenance Guidelines
Regular maintenance prolongs dryer life and ensures safety.
- Clean Lint Screen: After every load to improve efficiency and prevent fire.
- Inspect Vent Duct: Annually; remove lint buildup; use rigid metal duct.
- Check Drum Seals: Look for wear; replace if torn to prevent heat loss.
- Lubricate Bearings: Some models require periodic lubrication (refer to manual).
- Test Safety Features: Verify thermal fuse and thermostat operation yearly.
WARNING! Lint accumulation is a fire hazard; clean regularly.
Specifications
- Type: Electric or Gas Dryer (model dependent).
- Capacity: Typically 7.0 to 7.5 cubic feet.
- Power Requirements: Electric: 240V, 30A; Gas: 120V, 15A.
- Dimensions: Approx. 27" W x 29" D x 43" H.
- Weight: Approx. 130 lbs (empty).
- Vent Diameter: 4-inch standard.
- Cycle Options: Multiple heat settings, timed dry, sensor dry.
- Warranty: 1-year limited parts and labor; 10-year drum warranty.
Warranty Information
Kenmore Elite dryers come with limited warranties.
- Parts: 1-year coverage on functional components.
- Labor: 1-year in-home service for defects.
- Drum: 10-year warranty against corrosion/perforation.
- Conditions: Warranty valid for original owner; proof of purchase required.
- Exclusions: Damage from misuse, improper installation, or unauthorized repairs.
For warranty service, contact Kenmore at 1-800-469-4668 or visit kenmore.com.
Contact & Support
For technical assistance, parts ordering, or service.
- Customer Service: 1-800-469-4668 (Monday-Friday, 8AM-8PM EST).
- Parts Ordering: kenmoreparts.com or searspartsdirect.com.
- Online Resources: Manuals, diagrams, FAQs at kenmore.com.
- Authorized Service: Locate technicians via Kenmore website.
- Mailing Address: Kenmore Customer Care, PO Box 924, Louisville, KY 40201.
Note: Have model and serial numbers ready when contacting support.
Kenmore Elite Dryer Parts Manual © - All Rights Reserved 2025