Kenmore Elite Dryer Repair Manual 110

The Kenmore Elite Dryer Model 110 is a high-performance electric or gas dryer designed for residential use, featuring multiple drying cycles, temperature settings, moisture sensors, and advanced diagnostics. This manual provides comprehensive information for troubleshooting, maintenance, and repair of common issues such as no heat, not starting, unusual noises, and error codes. Below are key sections covering safety, model identification, components, troubleshooting, repair procedures, and parts replacement.

Model Identification & Specifications

Locate the model and serial number tag on the dryer frame (inside door or rear panel). Example: Kenmore Elite 110.XXXXXXX.

Safety Precautions

Always disconnect power before servicing. For gas models, shut off gas supply.

1. Unplug dryer or turn off circuit breaker.
2. For gas dryers: Turn gas valve to OFF position.
3. Allow dryer to cool completely before inspection.
4. Use insulated tools when testing electrical components.
5. Never bypass safety devices (thermal fuse, high-limit thermostat).

WARNING! Risk of electric shock, fire, or explosion. Only qualified technicians should perform repairs involving gas lines or high-voltage components.

Dryer Components Overview

Key parts: Drum, motor, blower, heating element (electric) or burner assembly (gas), thermostats, thermal fuse, moisture sensor, belts, idler pulley, timer/control board.

1. Front Panel: Contains control board, start switch, cycle selector.
2. Rear Panel: Access to heating element, thermostats, motor.
3. Top Panel: Lint filter housing, moisture sensor bars.
4. Base: Drum support rollers, belt, idler assembly.

CAUTION! Label wires and take photos before disassembly to ensure correct reassembly.

Common Symptoms & Diagnostics

• Dryer won't start: Check power supply, door switch, start switch, thermal fuse, timer/control board.
• No heat (electric): Test heating element, thermal fuse, high-limit thermostat, cycling thermostat.
• No heat (gas): Verify gas supply, igniter, flame sensor, gas valve coils, thermal fuse.
• Drum not turning: Inspect drive belt, motor, idler pulley, drum rollers.
• Overheating: Check venting for blockage, clean lint screen, verify thermostats.
• Unusual noises: Worn rollers, idler pulley, blower wheel, foreign objects in drum.
• Error codes on display: Refer to Error Code section (e.g., F-01, F-11).

Troubleshooting Flowcharts

Use systematic approach: Start with power, then controls, then mechanical components.

No Heat Flowchart (Electric): 1. Verify dryer runs but no heat. 2. Check thermal fuse continuity. 3. Test heating element for continuity (20-50 ohms). 4. Check cycling thermostat and high-limit thermostat. 5. Inspect wiring for breaks or burns.

Not Starting Flowchart: 1. Confirm power at outlet. 2. Check door switch continuity. 3. Test start switch. 4. Inspect thermal fuse. 5. Test motor windings. 6. Verify timer/control board operation.

Step-by-Step Repair Procedures

Accessing components requires removal of panels. Always disconnect power first.

1. Replace Thermal Fuse: Remove rear panel, locate fuse near vent, disconnect wires, install new fuse (194°F).
2. Replace Heating Element (Electric): Remove rear panel, disconnect wires, remove mounting screws, install new element.
3. Replace Drive Belt: Remove top panel, lift front panel, release tension on idler, route new belt around drum and motor pulley.
4. Replace Drum Rollers: Remove front panel and belt, unbolt old rollers, lubricate new roller shafts, reassemble.
5. Test Door Switch: Use multimeter to check for continuity when door is closed.
6. Clean Moisture Sensor: Wipe sensor bars with rubbing alcohol to remove lint/detergent buildup.

Tip: Take photos during disassembly and keep screws organized.

Error Code Definitions

Electronic models display fault codes. Common codes for Kenmore Elite 110 series:

Reset: Unplug dryer for 5 minutes to clear error codes.

Preventive Maintenance

Regular maintenance extends dryer life and prevents fires.

1. Clean lint filter after every load.
2. Inspect and clean vent duct every 6 months.
3. Check drum rollers and idler pulley annually for wear.
4. Verify dryer is level to reduce vibration.
5. Clean moisture sensor bars monthly.

CAUTION! Never operate dryer without lint filter. Ensure vent duct is metal (not plastic) and properly secured.

Parts List & Ordering

Common replacement parts for Model 110 series. Use exact part numbers from your model tag.

Order parts from authorized Kenmore suppliers or www.searspartsdirect.com.

Wiring Diagrams

Refer to diagram on back of dryer or in manual. Color codes: Black (L1), Red (L2), White (Neutral), Green (Ground). For gas models: Additional wiring for igniter, gas valve, flame sensor.

1. Electric Model: Heating element in series with thermostats and thermal fuse.
2. Gas Model: 120V circuit for motor, controls; separate circuit for igniter and gas valve.
3. Control Board: Connects to door switch, start switch, temperature sensors, motor.

Tip: Use multimeter to verify voltage and continuity at each component.

Technical Support & Warranty

Kenmore Elite dryers typically have 1-year full warranty, 10-year limited warranty on drum. For repair assistance:

Reset: Unplug for 5 minutes to reset control board. For persistent issues, contact certified technician.

Service Note: Gas line repairs must be performed by licensed professional.