Kenmore Elite Ice Maker Parts Manual

The Kenmore Elite Ice Maker Parts Manual provides detailed information on replacement parts, components, and maintenance for Kenmore Elite series ice makers. This manual includes part numbers, diagrams, ordering information, safety precautions, installation guidelines, troubleshooting, and compatibility details for various models. Below are key sections covering parts identification, ordering, installation, maintenance, and troubleshooting.

1. Parts Overview and Diagrams 2. Part Numbers and Descriptions 3. Ordering Replacement Parts 4. Installation Instructions 5. Maintenance and Cleaning 6. Troubleshooting Common Issues 7. Safety Precautions 8. Warranty Information 9. Model Compatibility 10. Contact and Support

Parts Overview and Diagrams

Key components include ice maker assembly, water inlet valve, ice mold thermostat, ejector blades, motor module, gear case, and housing.

ComponentDescription
Ice Maker AssemblyComplete unit including mold, motor, and ejector system
Water Inlet ValveControls water flow into the ice mold
Ice Mold ThermostatMonitors temperature to control freezing cycle
Ejector BladesRotates to release ice cubes from mold
Motor ModuleDrives the ejector mechanism and cycle timer
Gear CaseHouses gears for ejector blade rotation
Housing/CoverProtective outer casing
Harness/WiringElectrical connections for power and controls
Mounting BracketSecures ice maker to freezer wall
Water Fill TubeDirects water into the ice mold

Part Numbers and Descriptions

Refer to the model number on your ice maker for exact part compatibility.

  1. Ice Maker Assembly: Part #W10897278 (common for many Elite models).
  2. Water Inlet Valve: Part #WPW10306476.
  3. Thermostat: Part #WPW10227467.
  4. Ejector Blades: Part #W10897279.
  5. Motor Module: Part #WPW10306477.
  6. Gear Case Kit: Part #W10897280.
  7. Mounting Bracket: Part #W10897281.

NOTE: Always verify part numbers with your specific model before ordering.

Ordering Replacement Parts

To order parts, have your model number ready.

  1. Identify model number: Located on the ice maker label inside freezer.
  2. Contact authorized dealer: Use part numbers from this manual.
  3. Online ordering: Visit Kenmore parts website with model number.
  4. Verify compatibility: Confirm part matches your model before purchase.

CAUTION! Use only genuine Kenmore Elite parts to ensure safety and performance.

Installation Instructions

Maintenance and Cleaning

Regular maintenance ensures optimal performance and ice quality.

Cleaning Steps:

  1. Unplug refrigerator and shut off water supply.
  2. Remove ice maker assembly per installation instructions.
  3. Clean ice mold and ejector blades with mild detergent and warm water.
  4. Inspect water fill tube for mineral deposits; clean if necessary.
  5. Reassemble and test.

Frequency: Clean every 6 months or as needed based on water hardness.

Troubleshooting Common Issues

If ice maker is not working, check these common problems.

SymptomPossible CauseCorrective Action
No ice productionWater valve blocked, thermostat faultyCheck water supply; test thermostat; replace if defective.
Small or misshapen iceLow water pressure, mineral buildupClean water filter; inspect fill tube; descale if needed.
Ice not ejectingEjector blades stuck, motor failureManually rotate blades; check motor; replace motor module.
Continuous runningThermostat stuck, control board issueTest thermostat continuity; inspect control board connections.
Water leakageCracked mold, loose connectionsInspect mold for cracks; tighten water line fittings.

Reset: Unplug refrigerator for 5 minutes to reset electronic controls.

Safety Precautions

Always follow safety guidelines when servicing ice maker.

  1. Disconnect power before any repair or maintenance.
  2. Shut off water supply to prevent flooding.
  3. Use proper tools to avoid injury or damage.
  4. Do not attempt repairs beyond your skill level; contact professional.

WARNING! Risk of electric shock and water damage. Proceed with caution.

Warranty Information

Kenmore Elite ice makers are covered by limited warranty. Check your original purchase documents for warranty period and terms. Warranty typically covers defects in materials and workmanship but does not cover damage from misuse, improper installation, or unauthorized repairs. Keep receipt for warranty claims.

Model Compatibility

Parts listed are compatible with Kenmore Elite models including but not limited to: 106.XXXXXX, 795.XXXXXX, 596.XXXXXX series. Always cross-reference part numbers with your specific model. For full compatibility list, visit Kenmore parts website or contact customer service.

Contact and Support

For technical support, parts ordering, or service:

Have model and serial numbers ready when contacting support.

Kenmore Elite Ice Maker Parts Manual © - All Rights Reserved 2025