Kenmore Progressive Vacuum Manual

The Kenmore Progressive Vacuum is a powerful upright vacuum cleaner designed for deep carpet cleaning and versatile floor care. It features a multi-cyclonic filtration system, adjustable height settings, edge cleaning capability, HEPA filtration, onboard tools, and a large capacity dust cup. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly Instructions 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Using Attachments 7. Cleaning Modes 8. Maintenance Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Upright vacuum body, motorized brush roll, adjustable handle, dust cup with filter system, onboard tool storage, power cord, and various attachments.

Feature	Description
Multi-Cyclonic Filtration	Maintains suction power by separating dirt from air
Adjustable Cleaning Height	5 settings for different carpet types and bare floors
Edge Cleaning	Bristles extend to clean along baseboards and edges
HEPA Filtration	Traps 99.97% of dust and allergens
Motorized Brush Roll	Automatically adjusts for carpet or hard floors
Large Capacity Dust Cup	1.5 liter capacity with easy-empty mechanism
Onboard Tools	Crevice tool, upholstery brush, and dusting brush
Power Cord	25-foot retractable cord with cord wrap
Headlight	LED light illuminates dark areas under furniture
Washable Filters	Both pre-motor and post-motor filters are washable

Assembly Instructions

Unpack and inspect all components. Assemble on a clean, flat surface.

Attach handle: Align handle with vacuum body and secure with provided screws.
Install dust cup: Slide dust cup into place until it clicks securely.
Attach hose: Connect hose to vacuum body and secure with locking mechanism.
Install filters: Place pre-motor and HEPA filters in their designated compartments.
Attach tools: Store onboard tools in their designated holders.

WARNING! Ensure all parts are securely fastened before use. Keep hands clear of moving parts during assembly.

First-Time Setup

Prepare vacuum for initial use with these steps.

Check filters: Ensure both filters are properly installed and seated.
Adjust height: Set cleaning height appropriate for your flooring type.
Test suction: Plug in and turn on to verify proper operation.
Familiarize with controls: Practice using power switch, brush roll control, and cord release.
Empty dust cup: Ensure dust cup is empty before first use.

CAUTION! Always unplug vacuum before performing any maintenance or filter changes.

Specifications

Model Type: Upright vacuum cleaner
Motor Power: 12 amp motor with 120V AC operation
Filtration System: Multi-cyclonic with HEPA final filter
Dust Cup Capacity: 1.5 liters (dry)
Cord Length: 25 feet retractable
Cleaning Path: 13 inches wide
Height Settings: 5 adjustable positions
Weight: 18 pounds
Warranty: 1-year limited warranty
Noise Level: 75 dB maximum

Controls and Settings

Main controls located on handle and vacuum body.

Handle Controls: Power switch, brush roll on/off, suction adjustment dial.

Vacuum Body: Height adjustment lever, dust cup release button, cord release button, tool release buttons.

Height Settings: Position 1 (low pile carpet), Position 2 (medium pile), Position 3 (high pile), Position 4 (plush carpet), Position 5 (bare floors). Suction Control: Adjust from minimum to maximum suction for different surfaces. Brush Roll Control: Turn off for hard floors or delicate rugs.

Using Attachments

Accessories for specialized cleaning tasks.

Crevice Tool: For tight spaces, corners, and between cushions.
Upholstery Brush: Gentle cleaning of furniture, curtains, and car interiors.
Dusting Brush: Soft bristles for delicate surfaces, blinds, and lampshades.
Extension Wand: Extends reach for high cleaning and under furniture.

Tip: Always turn off vacuum before changing attachments. Ensure attachments click securely into place.

Cleaning Modes

Optimize cleaning for different surfaces.

Carpet Cleaning: Use appropriate height setting; engage brush roll for deep cleaning.
Hard Floor Cleaning: Set to highest position; disengage brush roll if desired.
Above Floor Cleaning: Use attachments for furniture, stairs, and ceilings.
Edge Cleaning: Position vacuum so edge cleaning bristles contact baseboards.
Spot Cleaning: Use minimum suction and appropriate attachment for small areas.

WARNING! Do not vacuum wet surfaces, liquids, or flammable materials. Avoid vacuuming sharp objects that could damage filters.

Maintenance Features

Regular maintenance ensures optimal performance.

Filter Cleaning: Wash pre-motor filter monthly; replace HEPA filter every 6-12 months. Brush Roll Maintenance: Remove hair and debris regularly; check for wear. Dust Cup Emptying: Empty when full or after each use for best suction. Belt Inspection: Check drive belt every 6 months for wear or damage.

Care & Cleaning

Unplug vacuum before any maintenance. Clean exterior with damp cloth only.

CAUTION! Do not immerse any part of vacuum in water. Allow all filters to dry completely before reinstalling.

Regulatory Information

UL Listed: Meets UL safety standards for household vacuum cleaners. Energy Star: Compliant with energy efficiency guidelines. Copyright © Kenmore; trademarks of Sears Brands, LLC. For support, visit www.kenmore.com or contact 1-800-469-4668. Manufactured to comply with U.S. and Canadian electrical standards.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Loss of suction	Full dust cup or clogged filter	Empty dust cup; clean or replace filters; check for clogs in hose.
Brush roll not spinning	Obstruction or worn belt	Remove debris from brush roll; check and replace drive belt if necessary.
Vacuum won't turn on	Power cord or switch issue	Check power outlet; inspect cord for damage; ensure power switch is engaged.
Unusual noise	Foreign object in brush roll or motor	Turn off immediately; check for and remove foreign objects.
Poor carpet cleaning	Incorrect height setting	Adjust height setting for carpet type; ensure brush roll is engaged.
Overheating	Clogged filters or blocked airflow	Clean all filters; check for obstructions; allow vacuum to cool before resuming.

Reset: Unplug for 30 minutes if motor overheats and shuts off automatically.

Service: 1-800-469-4668; www.kenmore.com