Kenmore Range Hood Model 233 Manual

The Kenmore Range Hood Model 233 is a versatile kitchen ventilation system designed to remove smoke, grease, and odors from your cooking area. It features multiple fan speeds, built-in lighting, aluminum mesh filters, and a sleek stainless steel finish. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Ductwork 7. Operation 8. Maintenance & Cleaning 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Stainless steel housing, Control Panel, Dual LED Lights, Aluminum Mesh Filters, Fan Motor, and Duct Connector.

Feature	Description
Control Panel	Touch controls for fan speed and lighting
Dual LED Lights	Energy-efficient lighting for the cooktop
Aluminum Mesh Filters	Removable and washable grease filters
Fan Motor	3-speed settings for ventilation control
Duct Connector	Standard 3.25" x 10" or 7" round duct adapter included
Power Cord	3-prong plug for standard 120V outlet
POWER	Turns range hood on/off
LIGHT	Controls LED lights
FAN SPEED	Adjusts between Low, Medium, and High
DELAY OFF	Continues ventilation for 10 minutes after cooking

Installation

Unpack and inspect contents. Ensure proper mounting surface and electrical connection.

Mounting: Secure hood to wall or cabinet using provided screws and brackets.
Ductwork: Connect to existing duct or install new duct to vent outdoors.
Electrical: Plug into dedicated 120V outlet or hardwire according to local codes.
Final Check: Ensure all connections are secure and filters are properly installed.

WARNING! Installation should be performed by a qualified technician. Ensure power is disconnected during installation.

First-Time Setup

After installation, perform initial setup.

Power on: Plug in or turn on circuit breaker.
Test controls: Press POWER, then test LIGHT and FAN SPEED buttons.
Check ventilation: Ensure air is properly venting outdoors.
Set preferences: Adjust fan speed and lighting as needed.

CAUTION! Do not operate without filters installed. Keep flammable materials away from hood.

Specifications

Model: 233
Power: 120V AC, 60Hz, 3.0A
Fan Speeds: 3 (Low, Medium, High)
Lighting: 2 x 3W LED
Airflow: Up to 400 CFM
Noise Level: ≤65 dB on high setting
Filters: Aluminum mesh (2 included)
Duct Size: 3.25" x 10" or 7" round
Dimensions: 30" wide x 19.5" deep x 7" height

Controls and Settings

Control Panel located on front of hood.

Buttons: POWER (turns hood on/off), LIGHT (turns LED lights on/off), FAN SPEED (cycles through Low, Medium, High), DELAY OFF (activates 10-minute shutoff timer).

Operation: Press POWER to activate hood. Use FAN SPEED to select ventilation level. Press LIGHT to illuminate cooktop. DELAY OFF continues fan operation after cooking ends.

Connecting to Ductwork

Proper duct connection is essential for effective ventilation.

Choose venting method: Vertical through roof or horizontal through wall.
Connect duct adapter: Use provided adapter for your duct size.
Secure connections: Use metal duct tape or clamps to seal joints.
Check exterior vent: Ensure damper opens freely when fan is on.

Tip: Use the shortest, straightest duct path possible for best performance.

Operation

For optimal performance during cooking.

Turn on: Press POWER button.
Select fan speed: Choose Low for simmering, Medium for regular cooking, High for frying or searing.
Use lighting: Press LIGHT when additional illumination is needed.
Delay off: Press DELAY OFF to continue ventilation after cooking is complete.
Turn off: Press POWER or allow delay timer to complete.

WARNING! Never leave hood unattended during high-heat cooking. Keep filters clean for proper airflow.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

Filters: Remove and wash aluminum mesh filters monthly in warm, soapy water.
Exterior: Wipe stainless steel surface with soft cloth and mild cleaner.
Interior: Clean fan blades and interior surfaces every 6 months.
Lights: Replace LED lights when they fail (consult manual for replacement procedure).

CAUTION! Always disconnect power before cleaning. Do not use abrasive cleaners on stainless steel.

Regulatory Information

UL Listed for household use. Complies with NSF/ANSI Standard 96 for grease filter materials. Manufactured for household residential use only. For support, visit www.kenmore.com or contact 1-800-536-6673.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Fan not working	Power issue/obstruction	Check power connection; ensure circuit breaker is on; remove any obstructions from fan.
Poor ventilation	Clogged filters/duct	Clean filters; check duct for obstructions; ensure damper opens freely.
Lights not working	Bulb failure/power	Replace LED lights; check power connection.
Excessive noise	Loose parts/duct vibration	Tighten all screws; secure duct connections; check for foreign objects in fan.
Motor overheating	Blocked airflow	Clean filters; ensure proper duct sizing; allow motor to cool before restarting.

Reset: Turn off power for 5 minutes, then restore power.

Service: 1-800-536-6673; www.kenmore.com