Kenmore Ultra Wash 2 Dishwasher Manual

The Kenmore Ultra Wash 2 Dishwasher is a high-performance kitchen appliance featuring multiple wash cycles, energy-saving options, adjustable racks, soil sensors, and a quiet operation design. It includes a built-in water heater, delay start, sanitize rinse option, and child lock. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Cycle Selection & Operation 8. Care & Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Control Panel, Upper and Lower Racks, Silverware Basket, Filter System, Detergent Dispenser, Rinse Aid Dispenser, Spray Arms.

FeatureDescription
Ultra Wash CycleHeavy-duty cleaning for pots and pans
Energy Saver CycleReduces energy and water usage
Delay StartPrograms wash cycle to begin later (1-24 hours)
Sanitize RinseHigh-temperature final rinse to kill bacteria
Soil SensorAutomatically adjusts wash time based on soil level
Adjustable Upper RackCan be raised/lowered to accommodate tall items
Quiet OperationSound insulation for low noise levels
Child LockLocks control panel to prevent accidental changes
Heated Dry OptionUses heat to dry dishes completely
Rinse Aid IndicatorLight alerts when rinse aid is low

Installation

Unpack and inspect contents. Ensure proper electrical and plumbing connections.

  1. Choose location: Under counter with adequate clearance for door and ventilation.
  2. Connect water supply: Attach hot water line (120°F recommended) to inlet valve.
  3. Connect drain hose: Secure to sink drain or garbage disposal with air gap.
  4. Electrical connection: Plug into grounded 120V, 60Hz outlet (dedicated circuit recommended).
  5. Level the dishwasher: Adjust leveling legs to ensure door seals properly.

WARNING! Installation should be performed by a qualified technician. Ensure water and electrical connections are secure to prevent leaks or shock hazard.

First-Time Setup

Before first use, run a rinse cycle to clean interior.

  1. Remove shipping materials: Take out all foam blocks and tape from interior.
  2. Load detergent and rinse aid: Fill detergent cup and rinse aid dispenser.
  3. Select cycle: Choose NORMAL WASH and press START.
  4. Set preferences: Adjust water hardness setting if needed (see manual).
  5. Test operation: Run a complete cycle to ensure proper functioning.

CAUTION! Use only detergents and rinse aids designed for dishwashers. Do not use hand soap or laundry detergent.

Specifications

Controls and Settings

Control Panel: POWER, CYCLE SELECTION (Ultra Wash, Normal, Light, Rinse Only, Energy Saver), OPTIONS (Heated Dry, Sanitize, Delay Start), START/RESET.

Indicator Lights: Clean, Sanitized, Low Rinse Aid, Door Locked.

Cycle Settings: Ultra Wash (2.5 hours, high temp), Normal (2 hours), Light (1 hour), Rinse Only (15 minutes), Energy Saver (reduced temp/time). Options: Heated Dry (adds 30 minutes), Sanitize (maintains 150°F final rinse), Delay Start (1-24 hours). Settings: Water hardness (adjust via dip switches), Sound On/Off (beep control), Child Lock (press and hold START for 3 seconds).

Loading the Dishwasher

Proper loading ensures optimal cleaning and prevents damage.

  1. Scrape off large food particles (no pre-rinsing required).
  2. Lower rack: Place plates, pots, pans facing center. Use adjustable tines for bowls.
  3. Upper rack: Cups, glasses, small bowls. Fold-down tines for stemware.
  4. Silverware basket: Mix utensils handle-up/down for thorough cleaning.
  5. Detergent: Use recommended amount (check water hardness). Fill both cups for heavy soil.
  6. Rinse aid: Adjust dispenser setting based on water spots (1-6).

Tip: Do not overload. Ensure spray arms can rotate freely and items don't block detergent dispenser.

Cycle Selection & Operation

Select cycle based on soil level and dish type.

  1. Power on: Press POWER button.
  2. Select cycle: Press CYCLE button until desired light illuminates.
  3. Add options: Press OPTIONS for Heated Dry, Sanitize, or Delay Start.
  4. Start: Close door firmly and press START. Door locks during operation.
  5. Progress: Clean light flashes during wash, stays on when complete.
  6. Unloading: Wait for cycle to finish and door to unlock. Remove bottom rack first to prevent dripping.

WARNING! Do not open door during operation as hot water/steam may cause burns. Wait for door lock light to turn off.

Care & Maintenance

Regular maintenance ensures optimal performance and longevity.

  1. Monthly cleaning: Wipe door gasket and interior with damp cloth. Clean spray arm holes.
  2. Filter cleaning: Remove lower rack, twist out filter assembly, rinse under water.
  3. Detergent dispenser: Wipe clean to prevent clogs.
  4. Exterior: Clean with mild soap and soft cloth.
  5. Drain check: Ensure drain hose is not kinked.

CAUTION! Unplug before servicing. Do not use abrasive cleaners or steel wool on stainless interior.

Regulatory Information

UL Listed: Meets safety standards for household appliances. Energy Star® Certified: Meets energy efficiency guidelines. NSF Certified: Sanitize cycle meets NSF/ANSI 184 for sanitization performance. Copyright © Kenmore; trademarks of Sears Brands, LLC. For support, visit www.kenmore.com or contact 1-800-469-4668.

Troubleshooting

SymptomPossible CauseCorrective Action
Dishwasher won't startDoor not closed/powerEnsure door latched securely; check circuit breaker; plug in unit.
Poor cleaning resultsSpray arm blocked/detergentClear spray arm obstructions; use fresh detergent; check water temperature.
Water not drainingDrain clog/filterClean filter; check drain hose for kinks; ensure garbage disposal knockout plug removed.
Leaking waterDoor seal/detergentCheck door gasket for debris; ensure detergent dispenser closed; level dishwasher.
Unusual noiseSpray arm/rackEnsure spray arms rotate freely; check for utensils blocking spray arm; secure rack wheels.
Dishes not dryingHeated Dry option/rinse aidSelect Heated Dry option; refill rinse aid; use rinse aid setting 4-6.

Reset: Unplug for 1 minute or turn off circuit breaker for 30 seconds.

Service: 1-800-469-4668; www.kenmore.com

Kenmore Ultra Wash 2 Dishwasher Manual © - All Rights Reserved 2025