This parts manual provides detailed information, diagrams, and part numbers for Kenmore dryer models. It is intended for service technicians and qualified individuals to assist in the identification, ordering, and replacement of components. Below are key sections covering safety, model identification, exploded views, part lists, and troubleshooting guidance.
Before servicing any dryer, disconnect power at the circuit breaker or unplug the unit. Allow components to cool. Use proper tools and follow all safety procedures.
| Hazard | Precaution |
|---|---|
| Electrical Shock | Disconnect power before servicing. Verify with a voltmeter. |
| High Temperature | Allow dryer drum and heating elements to cool completely. |
| Moving Parts | Ensure drum and motor are secure and disconnected. |
| Gas Models | Shut off gas supply and check for leaks with soap solution after service. |
WARNING! Only qualified technicians should perform repairs involving electrical, gas, or mechanical systems.
Locate the model and serial number plate, typically found inside the door opening, on the back panel, or along the door frame.
Note: Always verify the model number before ordering parts. A single digit difference can indicate a different component.
Refer to the diagrams below for component location and assembly relationships.
Diagrams are model-specific. Consult the correct diagram for your model number.
This list corresponds to the exploded view diagrams. Parts are listed by assembly group.
| Ref # | Part Number | Description | Qty |
|---|---|---|---|
| 1 | W10012345 | Dryer Drum | 1 |
| 2 | 341241 | Drive Belt | 1 |
| 3 | 279834 | Motor (1/3 HP) | 1 |
| 4 | W10123456 | Heating Element (Electric) | 1 |
| 5 | WPW1000001 | Igniter (Gas Models) | 1 |
| 6 | 12001567 | Timer Control Knob | 1 |
| 7 | WPW1000002 | Door Switch | 1 |
| 8 | 3400923 | Idler Pulley Assembly | 1 |
| 9 | WPW1000003 | Thermal Fuse | 1 |
| 10 | W10012347 | Lint Screen | 1 |
Note: Part numbers are subject to change. Confirm with the latest parts catalog.
These are the most frequently replaced components for Kenmore dryers.
General steps for installing replacement parts. Always refer to specific service manual procedures.
Tip: Take photos during disassembly to aid reassembly. Ensure all connections are secure.
Use this table to diagnose common issues before ordering parts.
| Symptom | Possible Cause | Part to Check/Replace |
|---|---|---|
| Dryer does not start | Door switch, thermal fuse, start switch, power supply | Door Switch (WPW1000002), Thermal Fuse (WPW1000003) |
| No heat (Electric) | Heating element, thermal fuse, thermostats, timer | Heating Element (W10123456), Thermal Fuse |
| No heat (Gas) | Igniter, flame sensor, gas valve, thermal fuse | Igniter (WPW1000001), Thermal Fuse |
| Drum does not turn | Drive belt, idler pulley, motor, obstruction | Drive Belt (341241), Idler Pulley (3400923), Motor (279834) |
| Dryer runs but won't stop | Timer, electronic control board | Timer |
| Loud noise during operation | Idler pulley, drum support rollers, blower wheel, foreign object | Idler Pulley, Drum Glides/Rollers |
Reset: Unplug dryer for 2 minutes to reset electronic controls (if applicable).
To order parts, have your model number ready. Contact an authorized parts distributor or use the following resources.
Note: Some parts may be sold as kits. Verify shipping and return policies.
Original parts may be covered under the manufacturer's warranty. Service by a qualified technician is recommended for complex repairs.
Warranty: Check your original purchase documents. Replacement parts may have a 90-day or 1-year warranty from the parts supplier.
Service: For technical support or to schedule service, contact Sears Home Services at 1-800-469-4663 or visit www.searspartsdirect.com.
Disclaimer: This manual is for reference only. The manufacturer is not liable for injuries or damages resulting from repairs performed incorrectly.