Repair Manual for Kenmore Elite Gas Dryer

The Kenmore Elite Gas Dryer is a high-efficiency appliance designed for residential use, featuring multiple drying cycles, temperature settings, and advanced moisture sensing. This manual provides essential information for troubleshooting, maintenance, and repair procedures. Below are key sections covering safety, components, diagnostics, common repairs, and part replacement.

1. Safety Precautions 2. Model Identification & Parts 3. Tools Required 4. Diagnostic Codes & Troubleshooting 5. Disassembly Instructions 6. Common Repairs 7. Reassembly & Testing 8. Maintenance Schedule 9. Exploded View & Part Numbers 10. Warranty & Support

Safety Precautions

Before attempting any repair, ensure the dryer is unplugged and the gas supply is turned off. Work in a well-ventilated area and use appropriate personal protective equipment.

Hazard	Precaution
Electrical Shock	Disconnect power at breaker before servicing.
Gas Leaks	Turn off gas valve; check connections with soap solution after repair.
High Temperatures	Allow dryer to cool completely before disassembly.
Moving Parts	Keep hands clear of drum and belt during operation.
Sharp Edges	Wear gloves when handling internal components.

Model Identification & Parts

Locate the model and serial number on the door frame or rear panel. Use these to order correct replacement parts.

Model Number: Typically begins with "110." or "790."
Serial Number: 13-digit code for manufacturing date.
Common Parts: Thermal fuse, heating element, igniter, belt, rollers, idler pulley, gas valve solenoid.

WARNING! Using incorrect parts may cause malfunction or safety hazards.

Tools Required

Basic tools needed for most repairs:

Multimeter: For continuity and voltage tests.
Socket Set: 1/4" and 3/8" drive, 5/16" and 1/4" sockets common.
Screwdrivers: Phillips #2, flathead.
Pliers: Needle-nose, channel lock.
Putty Knife: For prying trim panels.
Nut Driver Set: For terminal connections.

Diagnostic Codes & Troubleshooting

Many models feature self-diagnostics. Enter service mode by pressing buttons in sequence (e.g., Temp Up + Temp Down + Start).

Code	Description	Possible Cause
F-01	Thermal Fuse Open	Overheat, restricted venting.
F-02	Cycling Thermostat Fault	Failed thermostat, wiring issue.
F-07	Motor Circuit	Brushes, centrifugal switch, wiring.
F-09	Gas Ignition Failure	Igniter, flame sensor, gas valve.
F-11	Moisture Sensor Error	Sensor bars, harness connection.

Disassembly Instructions

General steps to access internal components:

Unplug dryer and shut off gas.
Remove top panel: Insert putty knife at rear corners, release clips, lift panel.
Remove front panel: Take out screws at top, release spring clips at bottom.
Access drum: Remove belt, lift drum out after supporting front.
Access rear: Remove rear panel screws for heater assembly or motor.

Tip: Take photos during disassembly to aid reassembly.

Common Repairs

Step-by-step for frequent issues:

No Heat (Gas): Test igniter for continuity (30-50 ohms), check gas valve coils, verify flame sensor.
Drum Not Turning: Inspect belt for wear/cracks, check idler pulley tension, test motor brushes.
Dryer Overheating: Replace thermal fuse, clean lint from exhaust path, verify cycling thermostat.
Will Not Start: Check door switch, start switch, thermal fuse, and main control board.
Excessive Noise: Inspect rollers, glides, and drum support for wear; lubricate if applicable.

WARNING! Always test components with multimeter before replacement.

Reassembly & Testing

After repair, reassemble in reverse order. Ensure all connections are secure and no wires are pinched.

Reconnect all electrical and gas connections.
Verify belt routing around motor pulley and idler.
Replace panels and secure with screws.
Restore power and gas; run a test cycle empty.
Check for leaks, unusual noises, and proper heating.

CAUTION! Never operate the dryer without the drum belt properly installed.

Maintenance Schedule

Regular maintenance prevents common failures:

After Every Load: Clean lint filter.
Monthly: Inspect vent hose for kinks/blockages.
Every 6 Months: Vacuum lint from interior and motor area.
Annually: Have gas line and connections inspected by qualified technician.
As Needed: Replace worn rollers, glides, or belt.

Exploded View & Part Numbers

Refer to manufacturer diagrams for part location. Common Kenmore Elite Gas Dryer parts:

Part Description	Common Part Number
Thermal Fuse	3392519
Belt	341241
Igniter	279834
Gas Valve Solenoid	W10410038
Drum Roller	279640
Idler Pulley	W10003543

For exact parts, use model number at Sears Parts Direct.

Warranty & Support

Standard warranty: 1-year parts and labor from date of purchase. Extended warranties may apply. This repair manual is for qualified individuals; improper repair may void warranty.

Support: For technical assistance or part orders, contact Sears Home Services at 1-800-469-4663 or visit Sears Services. Always provide model and serial numbers.