sears kenmore vacuum model 116 owners manual

The Sears Kenmore Vacuum Model 116 is a powerful and reliable upright vacuum cleaner designed for deep carpet cleaning and versatile floor care. It features a robust motor, adjustable height settings, a built-in hose and tools, edge cleaning capability, and a large-capacity disposable dust bag. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Using Attachments 7. Operation Guide 8. Maintenance & Care 9. Safety Information 10. Warranty & Support 11. Troubleshooting

Features at a Glance

Key components: Powerful suction motor, Adjustable carpet height dial, On-board hose and tool storage, Edge cleaning capability, Large disposable dust bag, On/Off foot pedal, Cord wrap hooks.

FeatureDescription
MotorHigh-performance motor for deep carpet cleaning
Height AdjustmentDial for different carpet pile heights (Low, Medium, High)
On-Board ToolsBuilt-in hose, crevice tool, and upholstery nozzle
Edge CleaningBrushes extend to clean along baseboards
Dust BagLarge-capacity, easy-to-replace disposable bag
Foot PedalConvenient On/Off switch operated by foot
Cord WrapIntegrated hooks for power cord storage
Bag Full IndicatorVisual signal when bag needs replacement
HeadlightBuilt-in light for visibility under furniture (if equipped)
WheelsLarge rear wheels for easy maneuverability

Assembly & Installation

Unpack and inspect all parts. Assemble on a clean, flat surface.

  1. Attach Handle: Align handle with base unit and secure with provided screws.
  2. Install Dust Bag: Open bag compartment, insert new disposable bag, and secure latch.
  3. Attach Hose & Tools: Clip hose onto storage hooks; attach tools to designated holders.
  4. Wrap Power Cord: Wind cord around rear hooks for storage.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Setup

Prepare vacuum for initial use.

  1. Adjust Height: Set carpet height dial to match your floor type (start with Medium for most carpets).
  2. Check Bag: Ensure a new dust bag is properly installed and compartment is closed.
  3. Inspect Brush Roll: Verify brush roll spins freely and is clear of obstructions.
  4. Plug In: Connect power cord to a standard 120V AC outlet.

CAUTION! Do not use vacuum without a dust bag installed. Keep cord away from heated surfaces.

Specifications

Controls and Settings

Primary controls are located on the handle and base of the vacuum.

Handle: Carry handle, Hose release button. Base Unit: On/Off foot pedal, Height adjustment dial, Bag compartment latch, Cord release pedal.

Operation: Press foot pedal to start/stop. Adjust height dial for carpet (Low-pile, Medium, High-pile) or hard floors. Use hose release to detach hose for above-floor cleaning. Check bag indicator window; replace bag when full.

Using Attachments

For cleaning upholstery, stairs, crevices, and other above-floor areas.

  1. Detach Hose: Press hose release button on handle and pull hose out.
  2. Select Tool: Attach crevice tool, upholstery nozzle, or dusting brush to end of hose.
  3. Clean: Turn vacuum on with foot pedal; guide tool over surface.
  4. Re-stow: After use, detach tool, wrap hose around hooks, and clip tools in place.

Tip: For best suction, ensure hose and tools are free of clogs before use.

Operation Guide

Standard cleaning procedure for carpets and floors.

  1. Pre-Check: Ensure area is clear of large debris that could clog vacuum.
  2. Adjust Height: Set dial appropriately for your floor surface.
  3. Start Vacuum: Step on foot pedal to turn on.
  4. Cleaning Motion: Use slow, overlapping forward and backward strokes.
  5. Edge Cleaning: Tilt vacuum slightly to engage edge cleaning brushes.
  6. Shut Off: Step on pedal again to turn off. Unplug from outlet.
  7. Empty Bag: Replace bag when indicator shows full or suction decreases noticeably.

WARNING! Do not vacuum wet surfaces, hot ashes, or sharp objects. Keep hair, loose clothing, and fingers away from brush roll.

Maintenance & Care

Regular maintenance ensures optimal performance and longevity.

Bag Replacement: Unplug vacuum. Open bag compartment, remove full bag, dispose properly. Insert new bag, ensuring seal is secure. Close compartment.
Brush Roll Inspection: Periodically check for tangled hair or strings; cut and remove with scissors (unplug first).
Filter Check: If equipped with a secondary filter, clean or replace as per manual instructions.
Exterior Cleaning: Wipe down with a dry cloth. Do not use liquids or immerse in water.

CAUTION! Always disconnect power before performing any maintenance.

Safety Information

Read all instructions before use. For household use only.

Warranty & Support

This Kenmore product is backed by a Sears limited warranty. Proof of purchase is required. For service, contact Sears Customer Service or an authorized service center. For parts and accessories, visit www.searspartsdirect.com or call 1-800-469-4663.

Troubleshooting

SymptomPossible CauseCorrective Action
Loss of suctionFull bag, clog, or leakReplace dust bag. Check hose, tools, and inlet for blockages.
Brush roll not spinningObstruction or belt issueUnplug, remove bottom plate, clear debris. Inspect and replace drive belt if worn.
Vacuum won't turn onPower source, cord, or pedalCheck outlet and plug connection. Inspect cord for damage. Ensure foot pedal is engaged.
Excessive noise/vibrationForeign object in fan or brush rollUnplug immediately. Inspect brush roll and suction path for obstructions.
Leaving debris behindIncorrect height setting, full bagAdjust height dial. Replace dust bag if full.

For Service: 1-800-469-4663; www.sears.com

Sears Kenmore Vacuum Model 116 Owner's Manual © - All Rights Reserved 2025